ZB4-BS844
현행 제품Harmony XB4 Red Mushroom Emergency Stop (Push-Pull)
Red 40mm mushroom head emergency stop push button, push-pull reset, for Schneider Harmony XB4 series. 22mm cutout, IP66.
일반적인 용도
Emergency stop button found on CNC machines, hydraulic presses, industrial robots, and food processing lines. The 40mm mushroom head meets EN/ISO 13850 requirements — large enough to hit with a palm or forearm in a panic. Twist-to-release prevents accidental restart after an emergency — the operator must deliberately acknowledge the event before the machine can run again. Required by OSHA and EU Machinery Directive on any equipment with moving parts that could injure an operator.
주요 사용 설비
사양 목록
|
Actuator Type
The button head style. Flush sits level with the bezel (prevents accidental presses). Extended protrudes for easy access.
|
Mushroom Head
|
|
Certifications
Third-party safety certifications. UL = required for US NEC installations. CE = EU compliance. CSA = Canadian standards.
|
UL, CSA, CE, IEC 60947-5-5
|
|
Color
Button/actuator color. Green = start/go, Red = stop/emergency, Yellow = caution, Blue = reset (per IEC 60204-1).
|
Red
|
|
Contact Configuration
Normally Closed — circuit is on until you press. Standard for stop/emergency functions. Wire in series with safety circuits.
|
1NC (with ZB4-BZ102)
|
|
Cutout Diameter
The hole size you drill in your panel to mount this button. 22mm is the most common industrial standard worldwide.
|
22mm
|
|
Head diameter
|
40mm
|
|
IP Rating
IP66: Dust-tight and withstands powerful water jets from any direction. Standard for outdoor and washdown applications.
|
IP66
|
|
Material
The bezel/body material. Metal bezels are more durable in harsh environments. Plastic is lighter and cheaper.
|
Metal
|
|
Mounting Type
How the button attaches to the panel. Panel mount is standard — installs through a cutout from the front.
|
Panel
|
|
Reset type
|
Push-Pull
|
이 아이콘이 있는 사양은 제조사의 원본 출처 페이지에 연결되어 있습니다
추가로 필요한 부품
이것은 모듈형 부품입니다. 완전한 조립을 위해 다음이 추가로 필요할 수 있습니다:
호환 대체품
이 제품들은 다른 제조사의 기능적으로 동등한 호환품입니다.
설치 빠른 참조
Panel cutout: 22mm. Mount with the yellow backing plate visible (required by EN/ISO 13850).
Wiring: Wire NC contacts in series with the safety relay input channels. Use dual-channel wiring for SIL 3 / PLe applications. Never wire directly to a motor contactor.
Testing: Press the e-stop and verify the machine stops within the required time. Test the reset mechanism. Repeat monthly per EN/ISO 13850.
외형 치수
배선도
문제 해결
E-stop won't reset (twist/pull doesn't release)
Check for debris in the mechanism. For twist-release: turn clockwise 45-90 degrees. For push-pull: pull straight out firmly. If the mechanism is stuck, the internal latch may be damaged — replace the entire head assembly.
Machine doesn't stop when e-stop is pressed
Critical safety issue. Immediately lock out the machine. Check wiring — NC contacts must be in series with the safety relay. Verify the safety relay is functioning. A broken wire in an NC circuit should cause a stop, so check for a wiring bypass.
Safety relay faults after e-stop reset
The safety relay detects a cross-fault between the two monitoring channels. Check that both NC contacts on the e-stop are switching simultaneously. One contact may be welded closed — replace the contact block.
구매처
가격 범위
$4.56 — $68.61
4개 대리점
주요 사양
- Actuator Type
- Mushroom Head
- Certifications
- UL, CSA, CE, IEC 60947-5-5
- Color
- Red
- Contact Configuration
- 1NC (with ZB4-BZ102)
- Cutout Diameter
- 22mm
사용자 후기
“Always use NC contacts, always wire through a safety relay, always test monthly. The Schneider ZB4-BS844 twist-release is my go-to — the trigger guard prevents accidental activation. Never wire an e-stop directly to a contactor.”
자세히 보기
데이터 출처
사양 및 제품 데이터는 다음 참고 자료에서 수집되었습니다.
