Eaton · M22 Řada

M22-PVT45P

Aktivní
UL CSA CE IEC 60947-5-5

M22 Emergency Stop 45mm Mushroom Twist Release

Katalogové číslo: M22 - PVT45P
Eaton M22 Řada Introduced circa 2000
Eaton M22-PVT45P — M22 Emergency Stop 45mm Mushroom Twist Release

Red 45mm mushroom head emergency stop push button with twist-to-release reset for Eaton M22 series. 22.5mm cutout, IP67.

Běžné aplikace

Heavy-duty emergency stop with an oversized 45mm mushroom head — 5mm larger than standard 40mm e-stops for even easier palm actuation in high-stress situations. The twist-to-release mechanism meets EN/ISO 13850 for Category 0 emergency stops. Found on large industrial presses, steel mill equipment, and heavy machinery where operators may be wearing thick gloves. The larger head also improves visibility from a distance on wide control panels. The IP67 rating suits harsh environments with coolant spray, metal dust, and vibration. Wire the 1NC contact in series with the safety relay or safety PLC input.

Specifikace

Actuator Type
Mushroom Head
Certifications
UL, CSA, CE, IEC 60947-5-5
Color
Red
Contact Configuration
1NC
Cutout Diameter
22.5mm
Head diameter
45mm
IP Rating
IP67
Material
Plastic
Mounting Type
Panel
Reset type
Twist Release

Specifikace s touto ikonou odkazují na původní stránku výrobce

Budete také potřebovat

Toto je modulární komponenta. Pro kompletní sestavu budete možná potřebovat také:

Stručný průvodce instalací

Panel cutout: 22.5mm. Mount with the yellow backing plate visible (required by EN/ISO 13850).

Wiring: Wire NC contacts in series with the safety relay input channels. Use dual-channel wiring for SIL 3 / PLe applications. Never wire directly to a motor contactor.

Testing: Press the e-stop and verify the machine stops within the required time. Test the reset mechanism. Repeat monthly per EN/ISO 13850.

Rozměry

Front 22.5mm cutout 40mm head Side panel terminals

Schéma zapojení

L T 21 22 NC (closed) opens on press

Řešení problémů

E-stop won't reset (twist/pull doesn't release)

Check for debris in the mechanism. For twist-release: turn clockwise 45-90 degrees. For push-pull: pull straight out firmly. If the mechanism is stuck, the internal latch may be damaged — replace the entire head assembly.

Machine doesn't stop when e-stop is pressed

Critical safety issue. Immediately lock out the machine. Check wiring — NC contacts must be in series with the safety relay. Verify the safety relay is functioning. A broken wire in an NC circuit should cause a stop, so check for a wiring bypass.

Safety relay faults after e-stop reset

The safety relay detects a cross-fault between the two monitoring channels. Check that both NC contacts on the e-stop are switching simultaneously. One contact may be welded closed — replace the contact block.

Stručné specifikace

Actuator Type
Mushroom Head
Certifications
UL, CSA, CE, IEC 60947-5-5
Color
Red
Contact Configuration
1NC
Cutout Diameter
22.5mm

Co říkají uživatelé

+

“M22-PVT45P meets EN/ISO 13850 requirements. Always wire NC contacts through a safety relay, never direct to contactor. Test monthly.”

Reddit r/PLC 12 hlasů Zobrazit vlákno →

Zdroje dat

Specifikace a produktové údaje pocházejí z následujících zdrojů.

Eaton M22-PVT45P Product Page

https://www.eaton.com/us/en-us/skuPage.M22-PVT45P.html

Zobrazeno March 29, 2026

Zdroj