XALD321
ActiveSchneider Harmony XALD 3-Button Station (green/red/green, XALD321)
Schneider XALD 3-button station — start, stop, and e-stop.
Common Applications
Complete motor control station: green start, red stop, and red mushroom e-stop in one IP66 enclosure. The standard for remote motor control on conveyors, pumps, and fans. Meets OSHA requirements for accessible e-stop within reach of the operator.
Research Notes
1. Overview
The Schneider Electric XALD321 (full catalog XALD321H29H7) is a pre-assembled 3-button control station from the Harmony XALD enclosed-station line — a dark-grey polycarbonate enclosure fitted with green flush / red flush / green flush Ø22 pushbuttons (XB5 22 mm operators). It's a ready-to-mount IP66 surface station for multi-function control (e.g. two start/function buttons + one stop, or forward/reverse/stop). (Data-quality note: this was mislabeled as a "Start/Stop/E-Stop" station with an emergency stop — the third operator is a green flush pushbutton, not an e-stop mushroom. Per Schneider's datasheet the operators are green / red / green.)
2. User Sentiment
Enclosed multi-button stations are valued for fast, standard installation — three factory-fitted operators in one box save assembling operators and contacts individually. Robust Harmony hardware, dark-grey/green-red-green presentation. Considerations: confirm the exact button functions and contacts for the control scheme (the green/red/green layout suits two-function + stop, or fwd/rev/stop — not an emergency-stop station).
3. Real-World Applications
Three-function machine control — e.g. two start/function buttons + one stop, or forward / reverse / stop — where a compact enclosed station is needed. For an actual E-STOP, use a red-mushroom station (e.g. XALK174E/178E), not this green/red/green unit.
4. Technical Specifications
- Type: Harmony XALD 3-button control station (enclosed, surface-mount)
- Operators: green flush / red flush / green flush Ø22 pushbuttons (XB5)
- Contacts: ~2 NO + 1 NC (greens NO, red NC) — verify against full catalog number
- Enclosure: dark-grey polycarbonate; IP66
- Approvals: UL, CSA, CE
5. Ordering & Compatibility
Complete populated station (green/red/green) — no separate operator/contact ordering. Full catalog number (e.g. XALD321H29H7) carries the exact configuration. For an empty 3-hole enclosure use XALD03; for an E-STOP station use a red-mushroom XALK/XALD variant. Uses standard Harmony XB5 22 mm service parts.
6. Known Issues / DQ
- DQ: this is a green/red/green 3-button station — not a Start/Stop/E-Stop station; there is no emergency-stop mushroom. Corrected here (function/color/contact attribution).
- Practical care: confirm the exact button functions and contact set from the full catalog number, and don't rely on this as an E-STOP (use a proper red-mushroom station for safety stop duty).
2 sources
Specifications
|
Certifications
Third-party safety certifications. UL = required for US NEC installations. CE = EU compliance. CSA = Canadian standards.
|
UL, CSA, CE
|
|
Color
Button/actuator color. Green = start/go, Red = stop/emergency, Yellow = caution, Blue = reset (per IEC 60204-1).
|
Green + Red + Green (three flush pushbuttons)
|
|
Contact Configuration
Normally Open — circuit is off until you press. Standard for start/go/enable functions.
|
~2NO + 1NC (verify from full catalog number)
|
|
Full catalog
|
XALD321H29H7
|
|
IP Rating
IP66: Dust-tight and withstands powerful water jets from any direction. Standard for outdoor and washdown applications.
|
IP66
|
|
Mounting Type
How the button attaches to the panel. Panel mount is standard — installs through a cutout from the front.
|
Surface mount (enclosed)
|
|
Operators
|
Green flush / red flush / green flush Ø22 (XB5) — NO e-stop mushroom
|
|
Pn note
|
Corrected: XALD321 = green/red/green 3-button station (se.com datasheet), NOT Start/Stop/E-Stop. The 3rd button is green flush, not an e-stop mushroom.
|
|
Pn status
|
mislabel-corrected
|
Installation Quick Reference
Panel cutout: 22mm. Insert from the front of the panel, secure with mounting nut from behind (tighten to 2-3 Nm).
Contact block: Snap or screw the contact block onto the rear of the button body. Ensure the contact block orientation matches the wiring diagram — NO terminals are usually marked.
Wiring: Use 0.5-2.5mm² stranded wire with ferrules. Tighten screw terminals to 0.8 Nm. Test the button function before energizing the circuit.
Dimensions
Wiring Diagram
Troubleshooting
Button doesn't respond when pressed
Check the contact block first — it's the most common failure point. Test continuity across the NO or NC terminals with a multimeter. If no click is felt, the return spring in the head may be broken.
Works intermittently
Contact block contacts are pitted or burned. Replace the contact block — don't try to file the contacts. Check if the rated cycle count has been exceeded.
Button feels mushy or doesn't click
The spring return mechanism in the button head is worn. Replace the head. The contact block can usually be reused if it tests OK.
Where to Buy
Price range
$5.37 — $45.32
across 2 sellers in US dollars
Quick Specs
- Certifications
- UL, CSA, CE
- Color
- Green + Red + Green (three flush pushbuttons)
- Contact Configuration
- ~2NO + 1NC (verify from full catalog number)
- Full catalog
- XALD321H29H7
- IP Rating
- IP66
What People Are Saying
“Complete motor control station: green start, red stop, and red mushroom e-stop in one IP66 enclosure. The standard for remote motor control on conveyors, pumps, and fans. Meets OSHA requirements for a”