ABB · Modular (MP) Seri

MPET4-10R

Name: ABB MPET4-10R
Brand: ABB
SKU: MPET4-10R
Price: 10.42 USD
Availability: InStock

Aktif

UL UL Listed — meets US safety standards. Required for NEC-inspected installations. CSA CSA Certified — meets Canadian safety standards. Required for installations in Canada. CE CE Marked — complies with EU directives (Low Voltage, Machinery, EMC). IEC 60947-5-5

Modular Red Mushroom Emergency Stop (Push-Pull)

Parça numarası: MP Modular Push Button series - 10R 1NO, Red (e-stop)

ABB Modular (MP) Seri Introduced circa 2005

ABB MPET4-10R — Modular Red Mushroom Emergency Stop (Push-Pull)

Red 40mm mushroom head emergency stop, ABB Modular series. Push-pull reset, 22mm cutout, IP65.

Yaygın Uygulamalar

ABB emergency stop with 40mm mushroom head and twist-to-release mechanism. Found on ABB robot cells, drive system panels, and industrial automation enclosures. The twist-release meets EN/ISO 13850 Category 0 stop requirements. In ABB robot installations, this e-stop is typically wired through the SafeMove safety controller — pressing it triggers a Category 0 stop (immediate power removal) on all axes.

Sıkça Bulunduğu Yerler

ABB IRB 6700 Robot Cell (Emergency Stop)

Sulzer APP Pump (Emergency Stop)

Teknik Özellikler

Actuator Type The button head style. Flush sits level with the bezel (prevents accidental presses). Extended protrudes for easy access.	Mushroom Head
Certifications Third-party safety certifications. UL = required for US NEC installations. CE = EU compliance. CSA = Canadian standards.	UL, CSA, CE, IEC 60947-5-5
Color Button/actuator color. Green = start/go, Red = stop/emergency, Yellow = caution, Blue = reset (per IEC 60204-1).	Red
Contact Configuration Normally Closed — circuit is on until you press. Standard for stop/emergency functions. Wire in series with safety circuits.	1NC
Cutout Diameter The hole size you drill in your panel to mount this button. 22mm is the most common industrial standard worldwide.	22mm
Head diameter	40mm
IP Rating IP65: Dust-tight and protected against low-pressure water jets. Suitable for indoor industrial and light washdown.	IP65
Material The bezel/body material. Metal bezels are more durable in harsh environments. Plastic is lighter and cheaper.	Plastic
Mounting Type How the button attaches to the panel. Panel mount is standard — installs through a cutout from the front.	Panel
Reset type	Push-Pull

Bu simgeye sahip özellikler, üreticinin orijinal kaynak sayfasına bağlantılıdır

Ayrıca İhtiyacınız Olacak

Bu modüler bir bileşendir. Tam montaj için ayrıca şunlara ihtiyacınız olabilir:

MCB-10 gerekli

1NO contact block for ABB modular push buttons

Uyumlu Alternatifler

Bu ürünler, diğer üreticilerden işlevsel olarak eşdeğer çapraz referanslardır.

Siemens

3SU1150-1HB20-1CH0

SIRIUS ACT Red Mushroom Emergency Stop (Push-Pull)

Schneider Electric

ZB4-BS844

Harmony XB4 Red Mushroom Emergency Stop (Push-Pull)

Eaton

M22-PV-K01

M22 Red Mushroom Emergency Stop (Push-Pull)

Hızlı Montaj Kılavuzu

Panel cutout: 22mm. Mount with the yellow backing plate visible (required by EN/ISO 13850).

Wiring: Wire NC contacts in series with the safety relay input channels. Use dual-channel wiring for SIL 3 / PLe applications. Never wire directly to a motor contactor.

Testing: Press the e-stop and verify the machine stops within the required time. Test the reset mechanism. Repeat monthly per EN/ISO 13850.

Boyutlar

Bağlantı Şeması

Sorun Giderme

E-stop won't reset (twist/pull doesn't release)

Check for debris in the mechanism. For twist-release: turn clockwise 45-90 degrees. For push-pull: pull straight out firmly. If the mechanism is stuck, the internal latch may be damaged — replace the entire head assembly.

Machine doesn't stop when e-stop is pressed

Critical safety issue. Immediately lock out the machine. Check wiring — NC contacts must be in series with the safety relay. Verify the safety relay is functioning. A broken wire in an NC circuit should cause a stop, so check for a wiring bypass.

Safety relay faults after e-stop reset

The safety relay detects a cross-fault between the two monitoring channels. Check that both NC contacts on the e-stop are switching simultaneously. One contact may be welded closed — replace the contact block.