MPET4-10R
सक्रियModular Red Mushroom Emergency Stop (Push-Pull)
Red 40mm mushroom head emergency stop, ABB Modular series. Push-pull reset, 22mm cutout, IP65.
सामान्य अनुप्रयोग
ABB emergency stop with 40mm mushroom head and twist-to-release mechanism. Found on ABB robot cells, drive system panels, and industrial automation enclosures. The twist-release meets EN/ISO 13850 Category 0 stop requirements. In ABB robot installations, this e-stop is typically wired through the SafeMove safety controller — pressing it triggers a Category 0 stop (immediate power removal) on all axes.
आमतौर पर पाया जाता है
स्पेसिफिकेशन
|
Actuator Type
The button head style. Flush sits level with the bezel (prevents accidental presses). Extended protrudes for easy access.
|
Mushroom Head
|
|
Certifications
Third-party safety certifications. UL = required for US NEC installations. CE = EU compliance. CSA = Canadian standards.
|
UL, CSA, CE, IEC 60947-5-5
|
|
Color
Button/actuator color. Green = start/go, Red = stop/emergency, Yellow = caution, Blue = reset (per IEC 60204-1).
|
Red
|
|
Contact Configuration
Normally Closed — circuit is on until you press. Standard for stop/emergency functions. Wire in series with safety circuits.
|
1NC
|
|
Cutout Diameter
The hole size you drill in your panel to mount this button. 22mm is the most common industrial standard worldwide.
|
22mm
|
|
Head diameter
|
40mm
|
|
IP Rating
IP65: Dust-tight and protected against low-pressure water jets. Suitable for indoor industrial and light washdown.
|
IP65
|
|
Material
The bezel/body material. Metal bezels are more durable in harsh environments. Plastic is lighter and cheaper.
|
Plastic
|
|
Mounting Type
How the button attaches to the panel. Panel mount is standard — installs through a cutout from the front.
|
Panel
|
|
Reset type
|
Push-Pull
|
इस आइकन वाले स्पेसिफिकेशन निर्माता के मूल स्रोत पृष्ठ से जुड़े हैं
आपको यह भी चाहिए
यह एक मॉड्यूलर घटक है। पूर्ण असेंबली के लिए, आपको ये भी चाहिए:
संगत विकल्प
ये उत्पाद अन्य निर्माताओं से कार्यात्मक रूप से समकक्ष क्रॉस-रेफ़रेंस हैं।
इंस्टॉलेशन त्वरित संदर्भ
Panel cutout: 22mm. Mount with the yellow backing plate visible (required by EN/ISO 13850).
Wiring: Wire NC contacts in series with the safety relay input channels. Use dual-channel wiring for SIL 3 / PLe applications. Never wire directly to a motor contactor.
Testing: Press the e-stop and verify the machine stops within the required time. Test the reset mechanism. Repeat monthly per EN/ISO 13850.
आयाम
वायरिंग डायग्राम
समस्या निवारण
E-stop won't reset (twist/pull doesn't release)
Check for debris in the mechanism. For twist-release: turn clockwise 45-90 degrees. For push-pull: pull straight out firmly. If the mechanism is stuck, the internal latch may be damaged — replace the entire head assembly.
Machine doesn't stop when e-stop is pressed
Critical safety issue. Immediately lock out the machine. Check wiring — NC contacts must be in series with the safety relay. Verify the safety relay is functioning. A broken wire in an NC circuit should cause a stop, so check for a wiring bypass.
Safety relay faults after e-stop reset
The safety relay detects a cross-fault between the two monitoring channels. Check that both NC contacts on the e-stop are switching simultaneously. One contact may be welded closed — replace the contact block.
कहाँ से खरीदें
मूल्य सीमा
$6.45 — $29.39
4 वितरकों से
संक्षिप्त स्पेसिफिकेशन
- Actuator Type
- Mushroom Head
- Certifications
- UL, CSA, CE, IEC 60947-5-5
- Color
- Red
- Contact Configuration
- 1NC
- Cutout Diameter
- 22mm
उपयोगकर्ता क्या कह रहे हैं
“MPET4-10R meets EN/ISO 13850 requirements. Always wire NC contacts through a safety relay, never direct to contactor. Test monthly.”
और जानें
डेटा स्रोत
स्पेसिफिकेशन और उत्पाद डेटा निम्नलिखित संदर्भों से प्राप्त।
ABB MPET4-10R Search Page
https://new.abb.com/products?q=MPET4-10R
एक्सेस किया गया March 29, 2026
