ZBE-1016P
Hoạt độngSchneider ZBE1016P Single Contact Block 1NO (Harmony XB4/XB5, gold-flash)
Schneider ZBE dual contact element — 1NO+1NC in one block.
Ứng Dụng Phổ Biến
Stacked dual contact element. 1NO for start signal + 1NC for PLC feedback, from a single stackable block. Saves space vs two separate blocks. Snaps onto any Harmony XB4/XB5 mounting base.
Tương thích
Fits all Schneider Harmony XB4, XB5, and legacy Telemecanique XB2 mounting bases. Stacks with other ZBE elements for up to 4 contacts per button.
Thông số kỹ thuật
|
Certifications
Third-party safety certifications. UL = required for US NEC installations. CE = EU compliance. CSA = Canadian standards.
|
UL, CSA, CE
|
|
Contact Configuration
Normally Open — circuit is off until you press. Standard for start/go/enable functions.
|
1NO (single contact block)
|
|
Contact material
|
Silver alloy, gold-flashed (low-level/logic current)
|
|
Mechanical Life
How many press cycles before mechanical failure. Higher is better — 10M cycles at 100 presses/day = 274 years.
|
10,000,000 cycles
|
|
Pn note
|
Corrected: ZBE1016P is a SINGLE 1NO contact block (se.com/RS), not 1NO+1NC stacked. Multi-contact sets are built by stacking blocks. Gold-flash = low-current capable.
|
|
Series
The manufacturer's product family. Products in the same series share mounting systems and accessories.
|
Harmony XB4/XB5 modular contact block
|
|
Terminal Type
How you connect wires. Screw clamp is most common in industrial. Spring cage is faster but requires proper ferrules.
|
Screw clamp
|
Hướng Dẫn Cài Đặt Nhanh
Mounting: Snap onto the rear of any compatible button body in the same series. The latch clicks audibly when properly seated. Some models require a mounting adapter.
Wiring: Terminals are marked NO (11/12) or NC (21/22). Use 0.5-2.5mm² wire with ferrules. Tighten to 0.8 Nm. Verify with a multimeter before energizing.
Kích thước
Sơ đồ đấu dây
Khắc phục sự cố
Intermittent switching
Silver contacts are pitted from arcing. Replace the contact block — they are consumable parts. If arcing is severe, check that the switched load doesn't exceed the contact rating (typically 6A at 120VAC).
Contact block won't snap onto button body
Verify the contact block series matches the button head series (e.g., Schneider ZB4 blocks fit ZB4 heads only, not ZB5). Check for debris or damage on the mounting tabs.
Nơi Mua Hàng
Dải giá
$13.89 — $48.57
từ 2 nhà phân phối
Thông số kỹ thuật nhanh
- Certifications
- UL, CSA, CE
- Contact Configuration
- 1NO (single contact block)
- Contact material
- Silver alloy, gold-flashed (low-level/logic current)
- Mechanical Life
- 10,000,000 cycles
- Pn note
- Corrected: ZBE1016P is a SINGLE 1NO contact block (se.com/RS), not 1NO+1NC stacked. Multi-contact sets are built by stacking blocks. Gold-flash = low-current capable.
Những Đánh Giá Từ Khách Hàng
“Stacked dual contact element. 1NO for start signal + 1NC for PLC feedback, from a single stackable block. Saves space vs two separate blocks. Snaps onto any Harmony XB4/XB5 mounting base.”
