MCB-10
Hoạt độngModular 1NO Contact Block
Single 1NO contact block for ABB Modular push button series. Snap-on mounting to operator heads. Screw terminals.
Ứng Dụng Phổ Biến
Contact block from ABB's modular pilot device system. The 1NO contact closes the circuit when the button is pressed — standard for start, enable, and jog functions. Snaps onto the rear of any ABB MP-series push button head using the modular mounting system. The 10A/600V rating handles direct switching of small contactors and relay coils. When troubleshooting an intermittent button on an ABB panel, swap this block first — contact blocks wear faster than the button head and are the most common point of failure. Compatible with MP1, MP2, MP3, and MPET4 series actuators.
Thông số kỹ thuật
|
Certifications
Third-party safety certifications. UL = required for US NEC installations. CE = EU compliance. CSA = Canadian standards.
|
UL, CSA, CE
|
|
Contact Configuration
Normally Open — circuit is off until you press. Standard for start/go/enable functions.
|
1NO
|
|
Current rating
|
10A
|
|
Terminal Type
How you connect wires. Screw clamp is most common in industrial. Spring cage is faster but requires proper ferrules.
|
Screw Clamp
|
|
Max Voltage
|
600V
|
Thông số kỹ thuật có biểu tượng này được liên kết đến trang nguồn gốc của nhà sản xuất
Bạn Cũng Cần
Đây là một thành phần mô-đun. Để lắp ráp hoàn chỉnh, bạn có thể cần thêm:
Các Lựa Chọn Tương Thích
Các sản phẩm này là các tham chiếu chéo tương đương về chức năng từ các nhà sản xuất khác.
Hướng Dẫn Cài Đặt Nhanh
Mounting: Snap onto the rear of any compatible button body in the same series. The latch clicks audibly when properly seated. Some models require a mounting adapter.
Wiring: Terminals are marked NO (11/12) or NC (21/22). Use 0.5-2.5mm² wire with ferrules. Tighten to 0.8 Nm. Verify with a multimeter before energizing.
Kích thước
Sơ đồ đấu dây
Khắc phục sự cố
Intermittent switching
Silver contacts are pitted from arcing. Replace the contact block — they are consumable parts. If arcing is severe, check that the switched load doesn't exceed the contact rating (typically 6A at 120VAC).
Contact block won't snap onto button body
Verify the contact block series matches the button head series (e.g., Schneider ZB4 blocks fit ZB4 heads only, not ZB5). Check for debris or damage on the mounting tabs.
Nơi Mua Hàng
Dải giá
$1.57 — $8.55
từ 4 nhà phân phối
Thông số kỹ thuật nhanh
- Certifications
- UL, CSA, CE
- Contact Configuration
- 1NO
- Current rating
- 10A
- Terminal Type
- Screw Clamp
- Max Voltage
- 600V
Những Đánh Giá Từ Khách Hàng
“Keep spares of these. Contact blocks are consumable parts — the first thing to check when a button starts acting intermittent. Cheap replacement, saves troubleshooting time.”
Tìm Hiểu Thêm
Nguồn Dữ Liệu
Thông số kỹ thuật và dữ liệu sản phẩm được trích dẫn từ các tài liệu tham khảo sau.