HW1B-V4F01-R
ใช้งานอยู่HW Emergency Stop 40mm Mushroom Twist Release
Red 40mm mushroom head emergency stop, IDEC HW series. Twist-to-release reset, 22mm cutout, IP65, with 1NC contact.
การใช้งานทั่วไป
IDEC emergency stop with 40mm mushroom head and twist-to-release mechanism meeting EN/ISO 13850. The 1NC contact provides fail-safe operation — circuit is closed during normal running and opens when the e-stop is pressed. Found on cost-effective machine builds, retrofit projects, and OEM equipment where IDEC's lower price point makes it attractive compared to Schneider or Siemens e-stops. The IP65 rating suits standard indoor industrial environments. Wire the NC contact in series with the safety relay or safety PLC module. Often paired with IDEC HW-series push buttons and the IDEC HR relay range for a single-vendor safety circuit.
ข้อมูลจำเพาะ
|
Actuator Type
The button head style. Flush sits level with the bezel (prevents accidental presses). Extended protrudes for easy access.
|
Mushroom Head
|
|
Certifications
Third-party safety certifications. UL = required for US NEC installations. CE = EU compliance. CSA = Canadian standards.
|
UL, CSA, CE, IEC 60947-5-5
|
|
Color
Button/actuator color. Green = start/go, Red = stop/emergency, Yellow = caution, Blue = reset (per IEC 60204-1).
|
Red
|
|
Contact Configuration
Normally Closed — circuit is on until you press. Standard for stop/emergency functions. Wire in series with safety circuits.
|
1NC
|
|
Cutout Diameter
The hole size you drill in your panel to mount this button. 22mm is the most common industrial standard worldwide.
|
22mm
|
|
Head diameter
|
40mm
|
|
IP Rating
IP65: Dust-tight and protected against low-pressure water jets. Suitable for indoor industrial and light washdown.
|
IP65
|
|
Material
The bezel/body material. Metal bezels are more durable in harsh environments. Plastic is lighter and cheaper.
|
Plastic
|
|
Mounting Type
How the button attaches to the panel. Panel mount is standard — installs through a cutout from the front.
|
Panel
|
|
Max Operating Temp
Highest temperature the button is rated to operate in.
|
65°C
|
|
Min Operating Temp
Lowest temperature the button is rated to operate in.
|
-25°C
|
|
Reset type
|
Twist Release
|
รายการสเปคที่มีไอคอนนี้เชื่อมโยงไปยังหน้าต้นฉบับของผู้ผลิต
ทางเลือกที่ใช้งานร่วมกันได้
ผลิตภัณฑ์เหล่านี้เป็นทางเลือกที่ใช้งานได้เหมือนกันจากผู้ผลิตรายอื่น
คู่มือการติดตั้งอย่างรวดเร็ว
Panel cutout: 22mm. Mount with the yellow backing plate visible (required by EN/ISO 13850).
Wiring: Wire NC contacts in series with the safety relay input channels. Use dual-channel wiring for SIL 3 / PLe applications. Never wire directly to a motor contactor.
Testing: Press the e-stop and verify the machine stops within the required time. Test the reset mechanism. Repeat monthly per EN/ISO 13850.
ขนาด
แผนภาพการเดินสายไฟฟ้า
การแก้ไขปัญหา
E-stop won't reset (twist/pull doesn't release)
Check for debris in the mechanism. For twist-release: turn clockwise 45-90 degrees. For push-pull: pull straight out firmly. If the mechanism is stuck, the internal latch may be damaged — replace the entire head assembly.
Machine doesn't stop when e-stop is pressed
Critical safety issue. Immediately lock out the machine. Check wiring — NC contacts must be in series with the safety relay. Verify the safety relay is functioning. A broken wire in an NC circuit should cause a stop, so check for a wiring bypass.
Safety relay faults after e-stop reset
The safety relay detects a cross-fault between the two monitoring channels. Check that both NC contacts on the e-stop are switching simultaneously. One contact may be welded closed — replace the contact block.
สถานที่จำหน่าย
ช่วงราคา
$5.75 — $35.72
จาก 4 ผู้จัดจำหน่าย
ข้อมูลจำเพาะอย่างย่อ
- Actuator Type
- Mushroom Head
- Certifications
- UL, CSA, CE, IEC 60947-5-5
- Color
- Red
- Contact Configuration
- 1NC
- Cutout Diameter
- 22mm
สิ่งที่ผู้คนพูดถึง
“For prototype and low-volume machines I use IDEC HW e-stops. They're UL listed, meet IEC 60947-5-5, and cost half of what Siemens charges. Not what I'd put in a food plant washdown, but for a dry lab or assembly cell they're perfectly adequate.”
เรียนรู้เพิ่มเติม
แหล่งข้อมูล
ข้อมูลจำเพาะและข้อมูลผลิตภัณฑ์อ้างอิงจากแหล่งข้อมูลต่อไปนี้
IDEC HW1B-V4F01-R Product Page
https://us.idec.com/idec-us/en/USD/Pushbuttons/.../p/HW1B-V4F01-R
เข้าถึงเมื่อ March 29, 2026
