M22-K01
AtivoM22 1NC Contact Block
Eaton M22 series 1NC contact block.
Aplicações comuns
1NC contact block for stop and safety circuits. The NC contact breaks the circuit when pressed — fail-safe design. Wire in series with motor contactor coil. Keep spares on hand — contact blocks are the most common failure point.
Notas de Pesquisa
CATALOG FLAG: This product is a contact block / contact element, NOT a complete pushbutton. It is a screw-terminal auxiliary contact that snaps onto the back of an M22 actuator/operator. Its presence in a button catalog should be flagged for review — it is a pushbutton accessory, not a pushbutton.
1. Overview
The Eaton (Moeller) M22-K01 is a single-pole normally-closed (1NC/SPST-NC) contact block (catalog number 216378) belonging to Eaton's RMQ-Titan M22 modular 22.5mm command-device system. It is a snap-on auxiliary contact element that mounts to the front of any M22 series actuator — pushbuttons, selector switches, emergency stop devices, key switches, and illuminated operators — and is not a standalone switch. The M22-K01 is the normally-closed counterpart of the M22-K10 (1NO); its cage-clamp terminal equivalent is the M22-CK01. The M22 system is a well-established heavy-duty industrial platform used globally across manufacturing, process control, and machine safety applications.
2. User Sentiment
No dedicated end-user forum reviews or community ratings were found for this specific part, which is typical of industrial contact blocks purchased by OEMs and panel builders rather than hobbyists. Distributors and integrators describe the M22 system broadly as "modular and flexible," highlighting field convertibility between maintained and momentary configurations and long service life (5M+ mechanical operations). The product is stocked by over 19 major distributors worldwide, indicating strong market acceptance. A Chinese industrial blog characterizes the M22-K01/K10 as suitable for standard control circuits, contrasting with the higher-current M22-KC01/KC10 for heavy-load applications.
3. Real-World Applications
The M22-K01 is used wherever a normally-closed control circuit contact is needed in a 22.5mm panel-mount operator assembly: machine start/stop signaling, PLC discrete input interfaces, operator station assemblies, alarm and indicator circuits, and — critically — emergency stop (e-stop) circuits. The contact's positive-opening (positively driven) design means the NC contacts are mechanically forced open on actuation even if contact springs fail or contacts weld, satisfying IEC 60947-5-1 and EN ISO 13850 safety requirements. The early-break characteristic of NC contacts (they open before any NO contacts close) is relevant for safety interlocking and e-stop wiring. The part is also listed for use as an auxiliary contact on NZM1–NZM4 circuit breakers.
4. Technical Specifications
- Type: Contact block / contact element (accessory — NOT a complete switch)
- Contact configuration: 1NC (SPST-NC), positively driven (positive opening per IEC/EN 60947-5-1)
- Terminal type: Screw terminals (cage-clamp equivalent: M22-CK01)
- Rated insulation voltage (Ui): 500 V AC
- Rated operational voltage (Ue) AC max: 500 V; DC max: 220 V
- Rated impulse withstand voltage (Uimp): 6,000 V
- Thermal current (Ith): 4 A (1-pole, open)
- AC-15 rated current (Ie) at 115–240 V: 6 A; at 380–415 V: 4 A; at 500 V: 2 A
- DC-13 rated current (Ie) at 24 V: 3 A; at 110 V: 0.6 A; at 220 V: 0.3 A
- Utilization categories: AC-15 / DC-13
- Overvoltage category: III; Pollution degree: 3
- Short-circuit protection: Max 10 A gG/gL fuse; fuseless with PKZM0-10/FAZ-B6/1
- IP rating: IP20 (contact block alone); IP66 / NEMA 4X / Type 13 achieved when assembled with M22 operator
- Temperature range: −25 °C to +70 °C
- Mechanical life: 5,000,000 operations; Electrical life: up to 1,600,000 operations (230 V, 0.5 A)
- Wire capacity: 0.5–2.5 mm² (stranded/solid); 0.5–1.5 mm² (flexible with ferrule)
- Mounting: Front fixing, top mounting and integrable; up to 6 contact blocks per operator (via M22-XW adapters)
- Dimensions: 38 mm (D) × 32 mm (W) × 10 mm (H); weight 0.01 kg / ~50 g
- Standards: IEC/EN 60947-5-1, UL 508, CSA C22.2 No. 14-05, VDE, CE; UL File E29184, CSA File 012528
- EAN: 4015082163785; Made in Germany
5. Ordering & Compatibility
The M22-K01 (Eaton catalog 216378) is widely available from major distributors including DigiKey, Mouser, RS Components, Newark/Farnell, Automation24, TME, Grainger, and WESCO, with typical street pricing around $7–$16 USD per unit. Bulk packs are available: M22-K01-B25 (25 units, Newark #53Y4446) and M22-K01-B100 (100 units). The cage-clamp terminal variant is M22-CK01. A GVP-suffix variant exists (M22-K01-GVP, catalog 216379, EAN 4015082163792). Compatible with all M22 series operators via front-snap attachment; M22-A adapter required for operators shipped without one (the M22-WRS selector switch, for example, includes the M22-A adapter prepackaged). Up to 6 contact blocks (NO/NC mix) can be stacked per operator using M22-XW intermediate adapters.
6. Known Issues
No significant field-reported issues or failure modes were found in the researched sources. The positive-opening design specifically addresses the risk of welded contacts in safety circuits. Installers should note the IP20 rating of the contact block itself — system-level IP66/NEMA 4X sealing requires the correct M22 operator and sealing ring assembly. The M22-K01 is not compatible with switch-disconnector PN series, and on NZM-XR remote operator combinations, the right-side mounting location requires individual contacts (not combined blocks).
Fonte
- 216378 | Eaton Moeller® series M22 contact element | Eaton — eaton.com
- 216378 | Eaton Moeller® series M22 contact element | Eaton (GB) — eaton.com
- 216378 | Eaton Moeller® series M22 Accessory Contact element | Eaton (BE) — eaton.com
- M22-K01 | Eaton M22 pushbutton contact block | Eaton (MX) — eaton.com
- PDF DATASHEET - M22-K01 (Eaton 216378 official) — simtaselektrik.com
- PDF Datasheet - M22-K01 (Dec 2024 revision) — klocknermoeller.com
- PDF Eaton M22-K01 Specification Sheet — eckartsupply.com
- M22-K01 Eaton Electrical | DigiKey Electronics — digikey.com
- M22-K01 Eaton Electrical | Switches | DigiKey (CA) — digikey.ca
- M22-K01 Eaton Electrical | Mouser India — mouser.in
- Eaton - Cutler Hammer M22-K01 Contact Block, SPST, 1NC, 6A 120VAC | RS US — rs-online.com
- 216378 M22-K01 | Eaton for Use with NZM1-4 Series, 500V AC, 1NC | RS ZA — rs-online.com
- 216378 M22-K01 | Eaton Contact Block, Screw Connection | RS AU — rs-online.com
- M22-K01 - Newark Electronics — newark.com
- M22-K01 EATON MOELLER, Contact Block, 1NC, 6A | Farnell Export — farnell.com
- M22-K01 EATON ELECTRIC - Contact block | TME US — tme.com
- M22-K01 EATON ELECTRIC - Contact block | TME EU — tme.eu
- Contact element Eaton 216378 - M22-K01 | Automation24 — automation24.com
- Eaton M22-K01 Contact Block | 1 N.C. | M22 Series 22.5mm — kentstore.com
- Eaton M22-K01 contact block, normally closed, front-mounted — imc-direct.com
- Eaton M22-WRS 22mm selector switch — M22-K01 add-on pricing — imc-direct.com
- EATON M22-K01 CONTACT BLOCK - IMS Supply — imssupply.com
- Eaton M22-K01 Terminal Contact Block - Aeliya Marine — aeliyamarine.net
- 216378 - M22-K01 Eaton Moeller | Shortec Electronics — shortec.com
- M22-K01 MOELLER Contact Block - VTC Solar (GR) — vtcsolar.gr
- M22-K01 Kontaktní prvek - EMAS CZ (Czech) — emas.cz
- Eaton RMQ-Titan M22-K01 Hulpcontactblok | Technische Unie (NL) — technischeunie.nl
- 进口eaton伊顿辅助触点m22-k01/M22-k10 对比 (ZH) — taobao.com
- M22-K01 - EATON MOELLER Contact Block, 4A, 500V | Faakart KSA — faakart.com
Compatibilidade
Same compatibility as M22-K10. NC version. Fits all M22 operators.
Reparo e manutenção
NC contacts are safety-critical — replace every 5 years as preventive maintenance on e-stop circuits regardless of test results.
Especificações
|
Certifications
Third-party safety certifications. UL = required for US NEC installations. CE = EU compliance. CSA = Canadian standards.
|
UL, CSA, CE
|
|
Contact Configuration
Normally Closed — circuit is on until you press. Standard for stop/emergency functions. Wire in series with safety circuits.
|
1NC
|
|
Mechanical Life
How many press cycles before mechanical failure. Higher is better — 10M cycles at 100 presses/day = 274 years.
|
10,000,000 cycles
|
|
Series
The manufacturer's product family. Products in the same series share mounting systems and accessories.
|
M22
|
|
Terminal Type
How you connect wires. Screw clamp is most common in industrial. Spring cage is faster but requires proper ferrules.
|
Screw clamp
|
Referência rápida de instalação
Mounting: Snap onto the rear of any compatible button body in the same series. The latch clicks audibly when properly seated. Some models require a mounting adapter.
Wiring: Terminals are marked NO (11/12) or NC (21/22). Use 0.5-2.5mm² wire with ferrules. Tighten to 0.8 Nm. Verify with a multimeter before energizing.
Dimensões
Diagrama de fiação
Solução de problemas
Intermittent switching
Silver contacts are pitted from arcing. Replace the contact block — they are consumable parts. If arcing is severe, check that the switched load doesn't exceed the contact rating (typically 6A at 120VAC).
Contact block won't snap onto button body
Verify the contact block series matches the button head series (e.g., Schneider ZB4 blocks fit ZB4 heads only, not ZB5). Check for debris or damage on the mounting tabs.
Onde comprar
Faixa de preço
$47.63 — $74.4
across 2 sellers in US dollars
Especificações rápidas
- Certifications
- UL, CSA, CE
- Contact Configuration
- 1NC
- Mechanical Life
- 10,000,000 cycles
- Series
- M22
- Terminal Type
- Screw clamp
O que os usuários dizem
“1NC contact block for stop and safety circuits. The NC contact breaks the circuit when pressed — fail-safe design. Wire in series with motor contactor coil. Keep spares on hand — contact blocks are th”