A22-FY-10M
현행 제품A22 Yellow Flush Push Button (1NO)
Yellow flush momentary push button, Omron A22 series. 22mm cutout, IP65, with 1NO contact. Screw terminals.
일반적인 용도
Yellow push button from the Omron A22 series used for intervention functions — fault reset, alarm acknowledgement, and jam-clear operations per IEC 60204-1 color standards. Found on Omron-controlled packaging machines, electronics assembly lines, and food processing equipment built by Japanese and Asian machine builders. The 1NO contact is typically wired to an Omron CJ/NJ PLC input for fault-reset logic. Note the narrower operating temperature range (-10 to 55 degrees C) compared to European brands — suitable for indoor factory environments but not cold storage. Pairs with the A22-FG-10M (green) and A22-FR-01M (red).
사양 목록
|
Actuator Shape
The physical shape of the pressable surface.
|
Round
|
|
Actuator Type
The button head style. Flush sits level with the bezel (prevents accidental presses). Extended protrudes for easy access.
|
Flush
|
|
Certifications
Third-party safety certifications. UL = required for US NEC installations. CE = EU compliance. CSA = Canadian standards.
|
UL, CSA, CE
|
|
Color
Button/actuator color. Green = start/go, Red = stop/emergency, Yellow = caution, Blue = reset (per IEC 60204-1).
|
Yellow
|
|
Contact Configuration
Normally Open — circuit is off until you press. Standard for start/go/enable functions.
|
1NO
|
|
Cutout Diameter
The hole size you drill in your panel to mount this button. 22mm is the most common industrial standard worldwide.
|
22mm
|
|
IP Rating
IP65: Dust-tight and protected against low-pressure water jets. Suitable for indoor industrial and light washdown.
|
IP65
|
|
Material
The bezel/body material. Metal bezels are more durable in harsh environments. Plastic is lighter and cheaper.
|
Plastic
|
|
Mounting Type
How the button attaches to the panel. Panel mount is standard — installs through a cutout from the front.
|
Panel
|
|
Max Operating Temp
Highest temperature the button is rated to operate in.
|
55°C
|
|
Min Operating Temp
Lowest temperature the button is rated to operate in.
|
-10°C
|
|
Terminal Type
How you connect wires. Screw clamp is most common in industrial. Spring cage is faster but requires proper ferrules.
|
Screw
|
이 아이콘이 있는 사양은 제조사의 원본 출처 페이지에 연결되어 있습니다
호환 대체품
이 제품들은 다른 제조사의 기능적으로 동등한 호환품입니다.
설치 빠른 참조
Panel cutout: 22mm. Insert from the front of the panel, secure with mounting nut from behind (tighten to 2-3 Nm).
Contact block: Snap or screw the contact block onto the rear of the button body. Ensure the contact block orientation matches the wiring diagram — NO terminals are usually marked.
Wiring: Use 0.5-2.5mm² stranded wire with ferrules. Tighten screw terminals to 0.8 Nm. Test the button function before energizing the circuit.
외형 치수
배선도
문제 해결
Button doesn't respond when pressed
Check the contact block first — it's the most common failure point. Test continuity across the NO or NC terminals with a multimeter. If no click is felt, the return spring in the head may be broken.
Works intermittently
Contact block contacts are pitted or burned. Replace the contact block — don't try to file the contacts. Check if the rated cycle count has been exceeded.
Button feels mushy or doesn't click
The spring return mechanism in the button head is worn. Replace the head. The contact block can usually be reused if it tests OK.
구매처
가격 범위
$2.39 — $5.67
3개 대리점
주요 사양
- Actuator Shape
- Round
- Actuator Type
- Flush
- Certifications
- UL, CSA, CE
- Color
- Yellow
- Contact Configuration
- 1NO
사용자 후기
“Solid button for panel builds. Omron A22 series is well-proven in the field. Standard 22mm mounting means easy replacement if needed.”
자세히 보기
데이터 출처
사양 및 제품 데이터는 다음 참고 자료에서 수집되었습니다.