3SU10000AB200AD0

現行品

Siemens 3SU10000AB200AD0

型番: 3SU1 - 0 - 20
Siemens 3SU10000AB200AD0 — Siemens 3SU10000AB200AD0

Switch Actuators PUSHBUTTON, MOM, RED, FLUSH

研究ノート

1. What this is

3SU10000AB200AD0 is a Siemens SIRIUS ACT 3SU1 22mm modular command switch. 3SU10 = actuator/holder or contact/lamp module (sold separately); 3SU11 = complete pre-assembled unit. Metal or plastic, huge function range (pushbutton, selector, indicator, E-stop).

2. Part-number decode

  • Series: 3SU1 (SIRIUS ACT)
  • Panel cutout: 22mm
  • Construction: modular (operator + holder + contact/lamp modules are separate parts)

3. Compatibility & ordering

Siemens 22mm command switches are modular IEC-style panel devices. Match by size, function (pushbutton/selector/indicator/E-stop), color, illumination, and contact blocks; cross-reference to Schneider Harmony, Allen-Bradley 800F, IDEC HW, or Eaton M22 by the same attributes if needed.

4. Data-quality note

The Siemens series is decoded from the part number (grounded in the Siemens LV1 catalog and distributor listings). The detailed configuration (exact function, color, contact arrangement, voltage) is encoded in the full order code and is left to the Siemens datasheet rather than guessed here. Flagged decoded-partial.

5. Sources

  • Siemens LV1 catalog / SIRIUS ACT (3SU) & Class 52 selection data (siemens.com)
  • Siemens Industry Mall — search the exact part/material number
  • Distributor listing (Mouser / Newark) — search the exact part number

出典
  1. Siemens Industry Mall — 3SU10000AB200AD0 — siemens.com
SIRIUS ACT (3SU1)シリーズについて

シリーズ全体に適用され、3SU10000AB200AD0 のみに限りません。

製品ラインについて

SIRIUS ACT (3SU1) は、Siemensのモジュラー式22mmプッシュボタン、セレクタースイッチ、キースイッチ、非常停止スイッチ、インジケーターライトの製品ラインです。以下の3つのデザインラインがあります:

  • 3SU1.0: プラスチック製フロントリング、ブラック、22mm
  • 3SU1.5: 光沢メタル、22mm
  • 3SU1.6: マットメタル、フラットフロント、30mm

2017年10月以降、旧モデルの3SB3、3SB1、3SF5シリーズを置き換え、2019年末までに在庫から消えました。Siemensは旧コードからの変換リストを公開しています(サポートエントリ109756490)。16mmの3SB2は別のシリーズです。

品番の仕組み

Siemensの品番は3SU1 ●●● – ● ●●●● – ●●●●の形式です。例として、3SU1100-0AB20-1BA0(赤色フラットプッシュボタン、1NO)を取り上げます:

位置意味値
3SU1の後の1桁目デバイスタイプ0 アクチュエーターまたはインジケーターのみ、1 完全ユニット、2 コンパクトユニット、4 モジュール、5 ホルダー、8 エンクロージャー、9 アクセサリー
2桁目フロントリング0 プラスチックブラック、5 光沢メタル、6 マットメタル
3桁目照明0 非照明、1 照明
ダッシュの後アクチュエータータイプ0 プッシュボタン、1 マッシュルーム/非常停止、2 セレクタースイッチ、3 ツイン/トグル、4–5 キースイッチ、6 インジケーターライトまたはブザー、7 コーディネートスイッチ
文字デザインと機能例:A フラット、B モーメンタリー
2桁色00 アンバー、10 ブラック、20 レッド、30 イエロー、40 グリーン、50 ブルー、60 ホワイト、70 クリア
最後のブロック接続と接点1 ネジ/3 スプリング端子;例:A 接点なし、B 1NO、C 1NC;マーキング(A なし、C "I"、D "O");最後の桁 2 = ATEX

最も一般的なミス: アクチュエーター単体(3SU10…、3SU15…、3SU16…、末尾-0AA0)にはホルダーも接点も含まれていません。動作させるためには、ホルダー(3SU1500-0AA10-0AA0 プラスチック、3SU1510-0AA10-0AA0 メタル、3SU1550-0AA10-0AA0 ユニバーサル)と接点モジュールを追加する必要があります。完全ユニット(3SU11…)には両方が含まれます。

セレクタースイッチ

機能文字(短いハンドルB、長いハンドルC)、アクチュエーターおよび完全ユニット:

  • BF: 2位置、ラッチング90°
  • BC: 2位置、センターから左へのスプリングリターン
  • BL: 3位置、ラッチング2 × 45°
  • BM: 3位置、両側からセンターへのスプリングリターン
  • BP / BN: 左からのスプリングリターン、右ラッチング / 左ラッチング、右からのリターン
  • GL: 3位置ラッチング、パッドロックでロック可能

例えば、3SU1052-2BL10-0AA0は光沢メタルの3位置ラッチングセレクターアクチュエーターです;ホルダーと接点が必要です。

接点モジュール(フロントプレート取り付け)

モジュール接点
3SU1400-1AA10-1BA01 NO
3SU1400-1AA10-1CA01 NC(ポジティブドライブ)
3SU1400-1AA10-1DA02 NO
3SU1400-1AA10-1EA02 NC
3SU1400-1AA10-1FA01 NO + 1 NC
3SU1400-1AA10-1HA01 NC(インストレーション監視付き:モジュールがホルダーから外れた場合に開く)

これらのコードでは、-1…の代わりに-3…はスプリング端子を意味します。定格:10A熱;AC-15 24–230Vで6A、400Vで3A;DC-13 24Vで3A、110Vで0.7A。機械寿命は1000万回操作です。接点はスローアクションで、5V/1mAまで信頼性があり、PLC入力に適しています。

製品ラインの定格(SiemensカタログIC 10, 2026)

  • ほとんどのアクチュエーターでIP66、IP67、IP69(IP69K)(4連プッシュボタンはIP65/IP66)
  • 動作温度 −25~+70°C(保管温度 −40~+80°C)。SchneiderのHarmonyは−40°Cまで対応。
  • 機械寿命:モーメンタリープッシュボタン1000万回操作、ラッチングプッシュボタン50万回、セレクタースイッチ100万回、非常停止スイッチ30万回
  • 衝撃15g;振動5g(10–500Hz);規格IEC 60947-1およびIEC 60947-5-1(非常停止スイッチはIEC 60947-5-5)

取り付け

穴径22.3mm(+0.4mm;Siemensでは22.5mmと呼ぶ)、パネル厚1–6mm、3位置ホルダー使用時は横方向に少なくとも30mm、上下方向に40mm離す必要があります(4位置ホルダー使用時は40×40mm)。ホルダーは背面からクリップで固定され、上部の1本のネジで締め付けられ、サイズ2のドライバーで1.0–1.2N·mで締めます;特別な工具は必要ありません。ホルダーは約4.5mmのパネル用にプリセットされているため、厚いパネルでは最初にネジを調整してください。ラベルホルダーと保護キャップは許容パネル厚を減らします。メタルホルダーをメタルパネルに取り付けると、ネジ先端を通じてアクチュエーターが接地されます。

購入時の注意点

  • 完全ユニット(3SU11…/3SU115…)を購入していることを確認してください。ホルダーと接点モジュールを持っていない限り、アクチュエーター単体を購入しないでください。
  • 色はコードから判断:…0AB20…は赤、…0AB60…は白です。ショップが誤って解読することがあるため、最後のダッシュの前の2桁を信頼してください。
  • 旧型の3SB3パーツは廃止されています。Siemensの変換リストを使用して3SU1の代替品を見つけてください;通常、ホルダーと接点モジュールも必要です。
  • 使用時の問題: 読める範囲の情報源では、繰り返し発生する故障パターンは見つかりませんでした。
出典
  1. Catalog IC 10 · 2026, chapter 13: Commanding and signaling devices (SIRIUS ACT) — Siemens
  2. System Manual SIRIUS ACT 3SU1 pushbuttons and signaling devices — Siemens
  3. Conversion list for the phase-out of 3SB3/3SB1/3SF5 to SIRIUS ACT (3SU1) — Siemens Industry Support
  4. SIRIUS 3SB3/3SB1/3SF5 phase-out (began October 2017) — Siemens Industry Mall
  5. SIRIUS ACT - Performance in Action (3SB3 not available after October 2019) — Siemens / RS

仕様一覧

Device class
command-switch
Enriched by
siemens-decoder-2026-08-12
Lead time
13 Days
Manufacturer series
3SU1 (SIRIUS ACT)
Modular
true
Mouser part number
982-3SU10000AB200AD0
Panel cutout
22mm
Pn status
decoded-partial
Rohs status
RoHS Compliant
Series description
Siemens SIRIUS ACT 3SU1 22mm modular command switch. 3SU10 = actuator/holder or contact/lamp module (sold separately); 3SU11 = complete pre-assembled unit. Metal or plastic, huge function range (pushbutton, selector, indicator, E-stop)

取付クイックリファレンス

Panel cutout: 22mm. Insert from the front of the panel, secure with mounting nut from behind (tighten to 2-3 Nm).

Contact block: Snap or screw the contact block onto the rear of the button body. Ensure the contact block orientation matches the wiring diagram — NO terminals are usually marked.

Wiring: Use 0.5-2.5mm² stranded wire with ferrules. Tighten screw terminals to 0.8 Nm. Test the button function before energizing the circuit.

外形寸法

トラブルシューティング

Button doesn't respond when pressed

Check the contact block first — it's the most common failure point. Test continuity across the NO or NC terminals with a multimeter. If no click is felt, the return spring in the head may be broken.

Works intermittently

Contact block contacts are pitted or burned. Replace the contact block — don't try to file the contacts. Check if the rated cycle count has been exceeded.

Button feels mushy or doesn't click

The spring return mechanism in the button head is worn. Replace the head. The contact block can usually be reused if it tests OK.

写真と図面

画像: mouser.com

主要仕様

Device class
command-switch
Enriched by
siemens-decoder-2026-08-12
Lead time
13 Days
Manufacturer series
3SU1 (SIRIUS ACT)
Modular
true