800F-1XA10-A1G
Active800F 1-Button Green Start Station Enclosed
Allen-Bradley 800F enclosed start station.
Common Applications
Complete AB start station in NEMA 4 enclosure. Pre-assembled 800F green button with 1NO contact. For remote start points on US industrial equipment.
Research Notes
1. What this is
800F-1XA10-A1G does not correspond to a real Allen-Bradley product. It was recorded in this catalog as "800F 1-Button Green Start Station Enclosed", but the code violates Rockwell's actual Bulletin 800F naming and returns no manufacturer or distributor results. If you found this exact code somewhere, it is almost certainly auto-generated or mistyped — treat it as non-existent.
2. Why it isn't real
Rockwell's genuine Bulletin 800F 22 mm pilot-device system uses:
- Colors as DIGITS, never letters: 1 = white, 3 = green, 4 = red, 5 = yellow, 6 = blue, 7 = black. Codes like "A7", "A1", "A4M1", "A8A8", "LW4" have no valid color field (there is no "A#" color, and 800F has no orange).
- Operators with actuator letters — e.g. 800FP-F3 (green flush), 800FP-F4 (red flush), 800FP-E3 (green extended). See the genuine operator entries in this catalog (#524 800FP-F3, #525 800FP-F4).
- Separate contact blocks — 800F-X10 (1 NO), 800F-X01 (1 NC) — that latch onto the operator (#523). 800F does not ship "complete/enclosed stations"; enclosed pushbutton stations are a different Rockwell line (800T / 800H, 30.5 mm). "Enclosed station" is not an 800F product class.
3. What you probably want instead
800F does not make enclosed stations. For a 1-button green start station, use an enclosed 800T / 800H station, or build one from an 800FP-F3 operator + 800F-X10 contact + an enclosure.
4. Why this page exists (data-quality)
Kept deliberately. The Button Index ranks for this exact code, so rather than show a misleading spec sheet, this page tells you the code isn't a real product and points you to the genuine 800F system. Flagged pn_status: fabricated. If you have a source proving otherwise, it can be reinstated.
2 sources
- Allen-Bradley Bulletin 800F 22mm push buttons (genuine naming) — rockwellautomation.com
- 800F 22mm Push Button Specifications / catalog-number decoder — rockwellautomation.com
Specifications
|
Certifications
Third-party safety certifications. UL = required for US NEC installations. CE = EU compliance. CSA = Canadian standards.
|
UL, CSA
|
|
Color
Button/actuator color. Green = start/go, Red = stop/emergency, Yellow = caution, Blue = reset (per IEC 60204-1).
|
Green
|
|
Contact Configuration
Normally Open — circuit is off until you press. Standard for start/go/enable functions.
|
1NO
|
|
IP Rating
Ingress Protection rating — first digit is dust (0-6), second is water (0-9). Higher is better.
|
NEMA 4
|
|
Mounting Type
How the button attaches to the panel. Panel mount is standard — installs through a cutout from the front.
|
Surface mount (enclosed)
|
|
Pn note
|
800F-1XA10-A1G does not resolve to a real product (only generic 800F literature + the 800F-X10 contact block). 800F is a 22mm OPERATOR/CONTACT-BLOCK line, NOT enclosed control stations (those are AB 800T/800H). Description is the fabricated boilerplate template shared with #430/#432 (1-Button Green Start Station Enclosed / green / 1NO). Joins the 800F fabricated cluster (#282/#283/#300/#301/#319/#332/#354). Flag/skip.
|
|
Pn status
|
fabricated / unverifiable
|
Installation Quick Reference
Panel cutout: 22mm. Insert from the front of the panel, secure with mounting nut from behind (tighten to 2-3 Nm).
Contact block: Snap or screw the contact block onto the rear of the button body. Ensure the contact block orientation matches the wiring diagram — NO terminals are usually marked.
Wiring: Use 0.5-2.5mm² stranded wire with ferrules. Tighten screw terminals to 0.8 Nm. Test the button function before energizing the circuit.
Dimensions
Wiring Diagram
Troubleshooting
Button doesn't respond when pressed
Check the contact block first — it's the most common failure point. Test continuity across the NO or NC terminals with a multimeter. If no click is felt, the return spring in the head may be broken.
Works intermittently
Contact block contacts are pitted or burned. Replace the contact block — don't try to file the contacts. Check if the rated cycle count has been exceeded.
Button feels mushy or doesn't click
The spring return mechanism in the button head is worn. Replace the head. The contact block can usually be reused if it tests OK.
Where to Buy
Price range
$5.33 — $84.97
across 2 distributors
Quick Specs
- Certifications
- UL, CSA
- Color
- Green
- Contact Configuration
- 1NO
- IP Rating
- NEMA 4
- Mounting Type
- Surface mount (enclosed)
What People Are Saying
“Complete AB start station in NEMA 4 enclosure. Pre-assembled 800F green button with 1NO contact. For remote start points on US industrial equipment.”