3SU1130-0AB60-1BA0
Hoạt độngSiemens SIRIUS ACT 3SU1 White Flush Pushbutton 1NO (3SU1130-0AB60-1BA0)
Siemens SIRIUS ACT orange push button.
Ứng Dụng Phổ Biến
Orange for plant-specific functions. Not standard IEC but available in the SIRIUS ACT range.
Research Notes
1. Overview
The Siemens 3SU1130-0AB60-1BA0 is a complete 22 mm SIRIUS ACT pushbutton — round, plastic with a metal front ring, white, flat (flush) actuator, momentary, with a 1 NO contact. It's an assembled unit (actuator + holder + contact) from Siemens' current SIRIUS ACT 3SU1 control-device line, rated IP67. (Data-quality note: this was cataloged as "Orange" — per Siemens/RS datasheet it is white (the color code "-0AB60-" = white). Corrected.)
2. User Sentiment
SIRIUS ACT is Siemens' modern, well-regarded 22 mm platform — valued for the plastic-with-metal-front-ring build, tool-free assembly, LED modules, and tight TIA/Siemens ecosystem fit. A complete white flush pushbutton is a neutral general-function control. The main care point is decoding the color and contact from the order number (as this entry shows, easy to mis-state).
3. Real-World Applications
General-purpose white (neutral/function) flush momentary button on machine and control panels — wired through the 1 NO contact for start/function/general control.
4. Technical Specifications
- Type: SIRIUS ACT 3SU1 complete pushbutton, 22 mm, flat/flush, momentary
- Color: white (code -0AB60-)
- Construction: round, plastic with metal front ring
- Contact: 1 NO (per the "-1BA0" suffix)
- Cutout: 22 mm
- Sealing: IP67
- Approvals: UL, CSA, CE
5. Ordering & Compatibility
Complete unit (actuator + holder + contact). The 3SU1 order number carries color and contact — confirm both (here white, 1 NO). Uses standard SIRIUS ACT 3SU1 modules for service (actuators, holders, contact/LED blocks). Metal-front-ring plastic version; a full-metal SIRIUS ACT variant also exists.
6. Known Issues / DQ
- DQ: color is white, not orange (per Siemens/RS datasheet). Corrected here.
- Practical care: decode color + contact from the full order number, confirm the 22 mm cutout, and match SIRIUS ACT service modules.
2 sources
Thông số kỹ thuật
|
Actuator Type
The button head style. Flush sits level with the bezel (prevents accidental presses). Extended protrudes for easy access.
|
Flush
|
|
Certifications
Third-party safety certifications. UL = required for US NEC installations. CE = EU compliance. CSA = Canadian standards.
|
UL, CSA, CE
|
|
Color
Button/actuator color. Green = start/go, Red = stop/emergency, Yellow = caution, Blue = reset (per IEC 60204-1).
|
White
|
|
Contact Configuration
Normally Open — circuit is off until you press. Standard for start/go/enable functions.
|
1NO
|
|
Cutout Diameter
The hole size you drill in your panel to mount this button. 22mm is the most common industrial standard worldwide.
|
22mm
|
|
Device type
|
SIRIUS ACT 3SU1 complete pushbutton (actuator+holder+1NO contact)
|
|
IP Rating
IP67: Dust-tight and survives temporary water submersion (1m for 30 min). Handles oil splashes, steam cleaning, and rain.
|
IP67
|
|
Material
The bezel/body material. Metal bezels are more durable in harsh environments. Plastic is lighter and cheaper.
|
Plastic with metal front ring
|
|
Pn note
|
Corrected: 3SU1130-0AB60-1BA0 = WHITE (Siemens/RS datasheet: white flat button, metal front ring). Was mislabeled Orange. Color code -0AB60- = white.
|
|
Pn status
|
color-corrected
|
Hướng Dẫn Cài Đặt Nhanh
Panel cutout: 22mm. Insert from the front of the panel, secure with mounting nut from behind (tighten to 2-3 Nm).
Contact block: Snap or screw the contact block onto the rear of the button body. Ensure the contact block orientation matches the wiring diagram — NO terminals are usually marked.
Wiring: Use 0.5-2.5mm² stranded wire with ferrules. Tighten screw terminals to 0.8 Nm. Test the button function before energizing the circuit.
Kích thước
Sơ đồ đấu dây
Khắc phục sự cố
Button doesn't respond when pressed
Check the contact block first — it's the most common failure point. Test continuity across the NO or NC terminals with a multimeter. If no click is felt, the return spring in the head may be broken.
Works intermittently
Contact block contacts are pitted or burned. Replace the contact block — don't try to file the contacts. Check if the rated cycle count has been exceeded.
Button feels mushy or doesn't click
The spring return mechanism in the button head is worn. Replace the head. The contact block can usually be reused if it tests OK.
Nơi Mua Hàng
Dải giá
$16.44 — $65.59
từ 3 nhà phân phối
Thông số kỹ thuật nhanh
- Actuator Type
- Flush
- Certifications
- UL, CSA, CE
- Color
- White
- Contact Configuration
- 1NO
- Cutout Diameter
- 22mm
Những Đánh Giá Từ Khách Hàng
“Orange for plant-specific functions. Not standard IEC but available in the SIRIUS ACT range.”
