3SU1130-0AB60-1BA0
ActivoSiemens SIRIUS ACT 3SU1 White Flush Pushbutton 1NO (3SU1130-0AB60-1BA0)
Siemens SIRIUS ACT orange push button.
Aplicaciones comunes
Orange for plant-specific functions. Not standard IEC but available in the SIRIUS ACT range.
Especificaciones
|
Actuator Type
The button head style. Flush sits level with the bezel (prevents accidental presses). Extended protrudes for easy access.
|
Flush
|
|
Certifications
Third-party safety certifications. UL = required for US NEC installations. CE = EU compliance. CSA = Canadian standards.
|
UL, CSA, CE
|
|
Color
Button/actuator color. Green = start/go, Red = stop/emergency, Yellow = caution, Blue = reset (per IEC 60204-1).
|
White
|
|
Contact Configuration
Normally Open — circuit is off until you press. Standard for start/go/enable functions.
|
1NO
|
|
Cutout Diameter
The hole size you drill in your panel to mount this button. 22mm is the most common industrial standard worldwide.
|
22mm
|
|
Device type
|
SIRIUS ACT 3SU1 complete pushbutton (actuator+holder+1NO contact)
|
|
IP Rating
IP67: Dust-tight and survives temporary water submersion (1m for 30 min). Handles oil splashes, steam cleaning, and rain.
|
IP67
|
|
Material
The bezel/body material. Metal bezels are more durable in harsh environments. Plastic is lighter and cheaper.
|
Plastic with metal front ring
|
|
Pn note
|
Corrected: 3SU1130-0AB60-1BA0 = WHITE (Siemens/RS datasheet: white flat button, metal front ring). Was mislabeled Orange. Color code -0AB60- = white.
|
|
Pn status
|
color-corrected
|
Referencia rápida de instalación
Panel cutout: 22mm. Insert from the front of the panel, secure with mounting nut from behind (tighten to 2-3 Nm).
Contact block: Snap or screw the contact block onto the rear of the button body. Ensure the contact block orientation matches the wiring diagram — NO terminals are usually marked.
Wiring: Use 0.5-2.5mm² stranded wire with ferrules. Tighten screw terminals to 0.8 Nm. Test the button function before energizing the circuit.
Dimensiones
Diagrama de cableado
Solución de problemas
Button doesn't respond when pressed
Check the contact block first — it's the most common failure point. Test continuity across the NO or NC terminals with a multimeter. If no click is felt, the return spring in the head may be broken.
Works intermittently
Contact block contacts are pitted or burned. Replace the contact block — don't try to file the contacts. Check if the rated cycle count has been exceeded.
Button feels mushy or doesn't click
The spring return mechanism in the button head is worn. Replace the head. The contact block can usually be reused if it tests OK.
Dónde comprar
Rango de precios
$16.44 — $65.59
en 3 distribuidores
Especificaciones rápidas
- Actuator Type
- Flush
- Certifications
- UL, CSA, CE
- Color
- White
- Contact Configuration
- 1NO
- Cutout Diameter
- 22mm
Lo que dicen los usuarios
“Orange for plant-specific functions. Not standard IEC but available in the SIRIUS ACT range.”
Más información
Grados de protección IP explicados
Qué significan IP65, IP66, IP67, IP69K para su aplicación
Guía 22mm vs. 30mm
¿Qué tamaño de corte de panel necesita?
Bloques de contacto: NO vs. NC
Cómo elegir y cablear bloques de contacto
Herramienta buscador de botones
Encuentre el botón correcto por tipo, tamaño y color
