XALK174E
AktifHarmony XALK 1-Button Red E-Stop Station
Schneider XALK enclosed e-stop station.
Yaygın Uygulamalar
Complete e-stop in a surface-mount enclosure. Yellow lid, red mushroom button, pre-wired NC contact. Mount anywhere — wall, post, machine frame. No panel needed. The standard remote e-stop for conveyor systems and large machines with multiple e-stop points.
Teknik Özellikler
|
Actuator Function
Momentary = springs back when released. Maintained/latching = stays pressed until pressed again.
|
Twist-release
|
|
Actuator Type
The button head style. Flush sits level with the bezel (prevents accidental presses). Extended protrudes for easy access.
|
Mushroom 40mm
|
|
Certifications
Third-party safety certifications. UL = required for US NEC installations. CE = EU compliance. CSA = Canadian standards.
|
UL, CSA, CE
|
|
Color
Button/actuator color. Green = start/go, Red = stop/emergency, Yellow = caution, Blue = reset (per IEC 60204-1).
|
Yellow enclosure, red Ø40 mushroom
|
|
Contact Configuration
Normally Closed — circuit is on until you press. Standard for stop/emergency functions. Wire in series with safety circuits.
|
1NC
|
|
IP Rating
IP65: Dust-tight and protected against low-pressure water jets. Suitable for indoor industrial and light washdown.
|
IP65
|
|
Mounting Type
How the button attaches to the panel. Panel mount is standard — installs through a cutout from the front.
|
Surface mount (enclosed)
|
|
Operator
|
1x red Ø40 mushroom E-stop, turn-to-release (XB5)
|
|
Series
The manufacturer's product family. Products in the same series share mounting systems and accessories.
|
Harmony XALD/XALK enclosed control station
|
Hızlı Montaj Kılavuzu
Panel cutout: 22mm. Mount with the yellow backing plate visible (required by EN/ISO 13850).
Wiring: Wire NC contacts in series with the safety relay input channels. Use dual-channel wiring for SIL 3 / PLe applications. Never wire directly to a motor contactor.
Testing: Press the e-stop and verify the machine stops within the required time. Test the reset mechanism. Repeat monthly per EN/ISO 13850.
Boyutlar
Bağlantı Şeması
Sorun Giderme
E-stop won't reset (twist/pull doesn't release)
Check for debris in the mechanism. For twist-release: turn clockwise 45-90 degrees. For push-pull: pull straight out firmly. If the mechanism is stuck, the internal latch may be damaged — replace the entire head assembly.
Machine doesn't stop when e-stop is pressed
Critical safety issue. Immediately lock out the machine. Check wiring — NC contacts must be in series with the safety relay. Verify the safety relay is functioning. A broken wire in an NC circuit should cause a stop, so check for a wiring bypass.
Safety relay faults after e-stop reset
The safety relay detects a cross-fault between the two monitoring channels. Check that both NC contacts on the e-stop are switching simultaneously. One contact may be welded closed — replace the contact block.
Nereden Satın Alınır
Fiyat aralığı
$37.35 — $143.76
2 distribütörde
Kısa Teknik Özellikler
- Actuator Function
- Twist-release
- Actuator Type
- Mushroom 40mm
- Certifications
- UL, CSA, CE
- Color
- Yellow enclosure, red Ø40 mushroom
- Contact Configuration
- 1NC
Kullanıcı Görüşleri
“Complete e-stop in a surface-mount enclosure. Yellow lid, red mushroom button, pre-wired NC contact. Mount anywhere — wall, post, machine frame. No panel needed. The standard remote e-stop for conveyo”
