2711R-T7T
ActivPanelView 800 7-inch HMI Touch Panel
Allen-Bradley PanelView 800 — Rockwells entry-level touchscreen HMI.
Aplicații frecvente
The standard HMI for Allen-Bradley/Rockwell panels. Replaces physical buttons with virtual controls on a 7-inch touch display. Connected View Designer software. Native integration with Micro800 and CompactLogix PLCs. Physical e-stop still required — the touchscreen cannot replace safety-rated buttons.
Research Notes
1. Overview
The Allen-Bradley 2711R-T7T is the 7-inch PanelView 800 graphic HMI terminal — a color touchscreen operator panel (800×480) in Rockwell's entry/economy HMI line, aimed at pairing with Micro800 PLCs and other small controllers. It's programmed with Connected Components Workbench (CCW) and connects via EtherNet/IP, Modbus (RTU/TCP), and serial (RS-232/422/485). IP65 front, panel-mount, UL/CSA/CE. The "-T7T" denotes Touch, 7-inch.
2. User Sentiment
Liked as an affordable, capable small HMI that integrates tightly with the Micro800/CCW ecosystem — good value for machine-level display, recipes, alarms, and trends. Common notes: it's an entry-tier terminal (fewer features and less horsepower than PanelView Plus), CCW is lighter than Studio 5000, and it's touch-only (no physical function keys on this model). Firmware/CCW version matching matters.
3. Real-World Applications
Local operator interface for small machines and OEM equipment driven by Micro820/850/870 (or other EtherNet-IP/Modbus controllers) — status/HMI screens, setpoints, alarms, and simple data logging on a 7" color touchscreen.
4. Technical Specifications
- Type: PanelView 800 HMI terminal, 7" color touchscreen
- Display: 7 in, 800×480 pixels, color
- Comms: EtherNet/IP, Modbus RTU/TCP, serial (RS-232/422/485), USB
- Software: Connected Components Workbench (CCW)
- Mounting: panel mount; IP65 (front)
- Approvals: UL, CSA, CE
5. Ordering & Compatibility
Order 2711R-T7T for the 7" touch model (siblings: 2711R-T4T 4", 2711R-T10T 10"). Designed to pair with Micro800 controllers and programmed in CCW; also talks EtherNet/IP and Modbus to other devices. Confirm CCW/firmware compatibility with your controller.
6. Known Issues
No notable reliability issues. Practical notes: it's an entry-level HMI (step up to PanelView Plus for advanced features/performance), touch-only (no tactile keys), and CCW/firmware versions should match the controller project. Standard HMI cautions (backlight lifetime, panel-cutout sealing) apply.
2 sources
- 2711R-T7T PanelView 800 7-inch HMI Terminal — rockwellautomation.com
- Allen Bradley PanelView 800 7in Touch HMI 800x480 — rs-online.com
Specificații
|
Certifications
Third-party safety certifications. UL = required for US NEC installations. CE = EU compliance. CSA = Canadian standards.
|
UL, CSA, CE
|
|
Config software
|
Connected Components Workbench (CCW); pairs with Micro800 PLCs
|
|
Display
|
7in color touchscreen, 800x480
|
|
Input
|
Touchscreen only (no physical function keys on -T7T)
|
|
IP Rating
IP65: Dust-tight and protected against low-pressure water jets. Suitable for indoor industrial and light washdown.
|
IP65 (front)
|
|
Mounting Type
How the button attaches to the panel. Panel mount is standard — installs through a cutout from the front.
|
Panel mount
|
|
Protocol
The wireless communication standard. BLE = short range, phone direct. Zigbee = mesh network, needs hub. Z-Wave = mesh, needs hub. WiFi = direct, higher power.
|
EtherNet/IP, Modbus RTU/TCP, serial (RS-232/422/485), USB
|
Referință rapidă de instalare
Panel cutout: 22mm. Insert from the front of the panel, secure with mounting nut from behind (tighten to 2-3 Nm).
Contact block: Snap or screw the contact block onto the rear of the button body. Ensure the contact block orientation matches the wiring diagram — NO terminals are usually marked.
Wiring: Use 0.5-2.5mm² stranded wire with ferrules. Tighten screw terminals to 0.8 Nm. Test the button function before energizing the circuit.
Dimensiuni
Depanare
Button doesn't respond when pressed
Check the contact block first — it's the most common failure point. Test continuity across the NO or NC terminals with a multimeter. If no click is felt, the return spring in the head may be broken.
Works intermittently
Contact block contacts are pitted or burned. Replace the contact block — don't try to file the contacts. Check if the rated cycle count has been exceeded.
Button feels mushy or doesn't click
The spring return mechanism in the button head is worn. Replace the head. The contact block can usually be reused if it tests OK.
De unde cumpărați
Interval de preț
$105.57 — $183.1
la 2 distribuitori
Specificații rapide
- Certifications
- UL, CSA, CE
- Config software
- Connected Components Workbench (CCW); pairs with Micro800 PLCs
- Display
- 7in color touchscreen, 800x480
- Input
- Touchscreen only (no physical function keys on -T7T)
- IP Rating
- IP65 (front)
Ce spun utilizatorii
“The standard HMI for Allen-Bradley/Rockwell panels. Replaces physical buttons with virtual controls on a 7-inch touch display. Connected View Designer software. Native integration with Micro800 and Co”
Aflați mai multe
Explicarea gradelor de protecție IP
Ce înseamnă IP65, IP66, IP67, IP69K pentru aplicația dvs.
Ghid 22mm vs 30mm
Ce dimensiune de decupaj în panou aveți nevoie?
Blocuri de contacte: NO vs NC
Cum alegeți și conectați blocurile de contacte
Instrument de căutare butoane
Găsiți butonul potrivit după tip, dimensiune și culoare