800F-2XA10-A1Y
Active800F 2-Button Start/Stop Station Enclosed
Allen-Bradley 800F 2-button start/stop control station.
Common Applications
Complete AB start/stop station in NEMA 4 enclosure. For remote motor control on US industrial equipment. Uses standard 800F buttons internally.
Research Notes
1. What this is
800F-2XA10-A1Y does not correspond to a real Allen-Bradley product. It was recorded in this catalog as "800F 2-Button Start/Stop Station Enclosed", but the code violates Rockwell's actual Bulletin 800F naming and returns no manufacturer or distributor results. If you found this exact code somewhere, it is almost certainly auto-generated or mistyped — treat it as non-existent.
2. Why it isn't real
Rockwell's genuine Bulletin 800F 22 mm pilot-device system uses:
- Colors as DIGITS, never letters: 1 = white, 3 = green, 4 = red, 5 = yellow, 6 = blue, 7 = black. Codes like "A7", "A1", "A4M1", "A8A8", "LW4" have no valid color field (there is no "A#" color, and 800F has no orange).
- Operators with actuator letters — e.g. 800FP-F3 (green flush), 800FP-F4 (red flush), 800FP-E3 (green extended). See the genuine operator entries in this catalog (#524 800FP-F3, #525 800FP-F4).
- Separate contact blocks — 800F-X10 (1 NO), 800F-X01 (1 NC) — that latch onto the operator (#523). 800F does not ship "complete/enclosed stations"; enclosed pushbutton stations are a different Rockwell line (800T / 800H, 30.5 mm). "Enclosed station" is not an 800F product class.
3. What you probably want instead
800F does not make enclosed stations. For a 2-button start/stop station, use an enclosed 800T / 800H station (e.g. 800T-T2…), or build one from 800FP operators + contact blocks + an enclosure.
4. Why this page exists (data-quality)
Kept deliberately. The Button Index ranks for this exact code, so rather than show a misleading spec sheet, this page tells you the code isn't a real product and points you to the genuine 800F system. Flagged pn_status: fabricated. If you have a source proving otherwise, it can be reinstated.
2 sources
- Allen-Bradley Bulletin 800F 22mm push buttons (genuine naming) — rockwellautomation.com
- 800F 22mm Push Button Specifications / catalog-number decoder — rockwellautomation.com
Specifications
|
Certifications
Third-party safety certifications. UL = required for US NEC installations. CE = EU compliance. CSA = Canadian standards.
|
UL, CSA
|
|
Color
Button/actuator color. Green = start/go, Red = stop/emergency, Yellow = caution, Blue = reset (per IEC 60204-1).
|
Green + Red
|
|
Contact Configuration
1NO + 1NC: One circuit closes and one opens when pressed. Common for start buttons that also signal 'running' state.
|
1NO + 1NC
|
|
IP Rating
Ingress Protection rating — first digit is dust (0-6), second is water (0-9). Higher is better.
|
NEMA 4
|
|
Mounting Type
How the button attaches to the panel. Panel mount is standard — installs through a cutout from the front.
|
Surface mount (enclosed)
|
|
Pn note
|
800F-2XA10-A1Y resolves to no product (only generic 800F operator/back-of-panel literature). 800F = 22mm operators/contact blocks, NOT enclosed control stations (those are AB 800T/800H). Same fabricated X-Button Start/Stop Station Enclosed boilerplate as #434. Joins 800F fabricated cluster. Flag/skip.
|
|
Pn status
|
fabricated / unverifiable
|
Installation Quick Reference
Panel cutout: 22mm. Insert from the front of the panel, secure with mounting nut from behind (tighten to 2-3 Nm).
Contact block: Snap or screw the contact block onto the rear of the button body. Ensure the contact block orientation matches the wiring diagram — NO terminals are usually marked.
Wiring: Use 0.5-2.5mm² stranded wire with ferrules. Tighten screw terminals to 0.8 Nm. Test the button function before energizing the circuit.
Dimensions
Wiring Diagram
Troubleshooting
Button doesn't respond when pressed
Check the contact block first — it's the most common failure point. Test continuity across the NO or NC terminals with a multimeter. If no click is felt, the return spring in the head may be broken.
Works intermittently
Contact block contacts are pitted or burned. Replace the contact block — don't try to file the contacts. Check if the rated cycle count has been exceeded.
Button feels mushy or doesn't click
The spring return mechanism in the button head is worn. Replace the head. The contact block can usually be reused if it tests OK.
Where to Buy
Price range
$137.42 — $170.58
across 2 sellers in US dollars
Quick Specs
- Certifications
- UL, CSA
- Color
- Green + Red
- Contact Configuration
- 1NO + 1NC
- IP Rating
- NEMA 4
- Mounting Type
- Surface mount (enclosed)
What People Are Saying
“Complete AB start/stop station in NEMA 4 enclosure. For remote motor control on US industrial equipment. Uses standard 800F buttons internally.”