PB4-2A
AktywnySecuritron Push-to-Exit Button Stainless
ASSA ABLOY Securitron PB4 push-to-exit button — stainless steel.
Typowe Zastosowania
The push-to-exit button next to the door in every office building, hospital, and secure facility. Press to unlock the magnetic lock and exit. Stainless steel face, vandal-resistant. Connected to access control panel via dry contact relay. When you press that silver button to leave a building, its probably a Securitron.
Specyfikacje
|
Actuator Function
Momentary = springs back when released. Maintained/latching = stays pressed until pressed again.
|
Momentary
|
|
Certifications
Third-party safety certifications. UL = required for US NEC installations. CE = EU compliance. CSA = Canadian standards.
|
UL, CE
|
|
Contact Configuration
The electrical switching arrangement.
|
SPDT (dry contact)
|
|
IP Rating
Ingress Protection rating — first digit is dust (0-6), second is water (0-9). Higher is better.
|
IP40
|
|
Material
The bezel/body material. Metal bezels are more durable in harsh environments. Plastic is lighter and cheaper.
|
Stainless Steel
|
|
Mounting Type
How the button attaches to the panel. Panel mount is standard — installs through a cutout from the front.
|
Surface mount or single-gang box
|
|
Vandal Rating (IK)
IK rating for impact resistance. IK09 = 10 joules (hammer blow). IK10 = 20 joules (serious vandalism). Higher is tougher.
|
IK08
|
Skrócona Instrukcja Montażu
Panel cutout: 22mm. Insert from the front of the panel, secure with mounting nut from behind (tighten to 2-3 Nm).
Contact block: Snap or screw the contact block onto the rear of the button body. Ensure the contact block orientation matches the wiring diagram — NO terminals are usually marked.
Wiring: Use 0.5-2.5mm² stranded wire with ferrules. Tighten screw terminals to 0.8 Nm. Test the button function before energizing the circuit.
Wymiary
Schemat Połączeń
Rozwiązywanie Problemów
Button doesn't respond when pressed
Check the contact block first — it's the most common failure point. Test continuity across the NO or NC terminals with a multimeter. If no click is felt, the return spring in the head may be broken.
Works intermittently
Contact block contacts are pitted or burned. Replace the contact block — don't try to file the contacts. Check if the rated cycle count has been exceeded.
Button feels mushy or doesn't click
The spring return mechanism in the button head is worn. Replace the head. The contact block can usually be reused if it tests OK.
Gdzie Kupić
Przedział cenowy
$48.32 — $64.89
u 2 dystrybutorów
Skrócone Specyfikacje
- Actuator Function
- Momentary
- Certifications
- UL, CE
- Contact Configuration
- SPDT (dry contact)
- IP Rating
- IP40
- Material
- Stainless Steel
Co Mówią Użytkownicy
“The push-to-exit button next to the door in every office building, hospital, and secure facility. Press to unlock the magnetic lock and exit. Stainless steel face, vandal-resistant. Connected to acces”
Dowiedz się Więcej
Objaśnienie Klasyfikacji IP
Co oznaczają IP65, IP66, IP67, IP69K dla Państwa zastosowania
Przewodnik 22mm vs 30mm
Jakiego rozmiaru otworu montażowego potrzebujesz?
Bloki Styków: NO vs NC
Jak wybrać i podłączyć bloki styków
Narzędzie Wyszukiwania Przycisków
Znajdź właściwy przycisk wg typu, rozmiaru i koloru