M22-DRP-R
ActivoEaton M22-DRP-R Red Maintained Mushroom Actuator (RMQ-Titan)
Eaton M22 red guarded push button.
Aplicaciones comunes
Same guard ring concept for Eaton panels. Prevents accidental activation. IP67 front face.
Especificaciones
|
Actuator Function
Momentary = springs back when released. Maintained/latching = stays pressed until pressed again.
|
Maintained (latching) — push to latch, pull/turn to release
|
|
Actuator Type
The button head style. Flush sits level with the bezel (prevents accidental presses). Extended protrudes for easy access.
|
Mushroom (maintained/latching)
|
|
Certifications
Third-party safety certifications. UL = required for US NEC installations. CE = EU compliance. CSA = Canadian standards.
|
UL, CSA, CE
|
|
Color
Button/actuator color. Green = start/go, Red = stop/emergency, Yellow = caution, Blue = reset (per IEC 60204-1).
|
Red
|
|
Contact Configuration
Normally Open — circuit is off until you press. Standard for start/go/enable functions.
|
None integral (head-only)
|
|
Cutout Diameter
The hole size you drill in your panel to mount this button. 22mm is the most common industrial standard worldwide.
|
22.5mm
|
|
Device type
|
M22 mushroom ACTUATOR (head-only); add contact block (e.g. K01)
|
|
IP Rating
IP67: Dust-tight and survives temporary water submersion (1m for 30 min). Handles oil splashes, steam cleaning, and rain.
|
IP67 (front)
|
|
Pn note
|
Corrected: M22-DRP-R = RED MAINTAINED (latching) MUSHROOM (DRP = D+R(Rastend/latching)+P(Pilz/mushroom)), not guarded/shrouded momentary. Latching counterpart to momentary M22-DP-R (#446). Not a certified e-stop (that=M22-PV/PVT).
|
|
Series
The manufacturer's product family. Products in the same series share mounting systems and accessories.
|
M22
|
Referencia rápida de instalación
Panel cutout: 22.5mm. Insert from the front of the panel, secure with mounting nut from behind (tighten to 2-3 Nm).
Contact block: Snap or screw the contact block onto the rear of the button body. Ensure the contact block orientation matches the wiring diagram — NO terminals are usually marked.
Wiring: Use 0.5-2.5mm² stranded wire with ferrules. Tighten screw terminals to 0.8 Nm. Test the button function before energizing the circuit.
Dimensiones
Diagrama de cableado
Solución de problemas
Button doesn't respond when pressed
Check the contact block first — it's the most common failure point. Test continuity across the NO or NC terminals with a multimeter. If no click is felt, the return spring in the head may be broken.
Works intermittently
Contact block contacts are pitted or burned. Replace the contact block — don't try to file the contacts. Check if the rated cycle count has been exceeded.
Button feels mushy or doesn't click
The spring return mechanism in the button head is worn. Replace the head. The contact block can usually be reused if it tests OK.
Dónde comprar
Rango de precios
$11.55 — $141.74
en 3 distribuidores
Especificaciones rápidas
- Actuator Function
- Maintained (latching) — push to latch, pull/turn to release
- Actuator Type
- Mushroom (maintained/latching)
- Certifications
- UL, CSA, CE
- Color
- Red
- Contact Configuration
- None integral (head-only)
Lo que dicen los usuarios
“Same guard ring concept for Eaton panels. Prevents accidental activation. IP67 front face.”
Más información
Grados de protección IP explicados
Qué significan IP65, IP66, IP67, IP69K para su aplicación
Guía 22mm vs. 30mm
¿Qué tamaño de corte de panel necesita?
Bloques de contacto: NO vs. NC
Cómo elegir y cablear bloques de contacto
Herramienta buscador de botones
Encuentre el botón correcto por tipo, tamaño y color