M22-I1-M1
AktivníEaton M22-I1 Empty 1-Hole M22 Control Station Enclosure (grey/black)
Eaton M22 enclosed single-button control station.
Běžné aplikace
Complete start station: M22 green button in an IP67 sealed enclosure with cable gland. Surface-mount for remote locations. The Eaton equivalent of Schneider XALK.
Research Notes
1. Overview
The Eaton M22-I1 (RS code RS-M22-I1-M1) is an empty one-element surface-mounting enclosure for the Eaton M22 / RMQ-Titan 22 mm modular system — a grey top / black base plastic box with one 22 mm hole into which you fit your own M22 actuator (pushbutton, e-stop, selector, indicator) plus contact/LED blocks. It ships empty (no button, no contacts), rated IP66, for building a single-operator control station. (Data-quality note: this was mis-cataloged as a "1-Button Green Start Station" with a green actuator and 1 NO contact — M22-I1 is an empty grey/black enclosure; there is no button or contact included.)
2. User Sentiment
The M22 surface enclosures are the standard way to make a stand-alone control station without a panel cutout — install one, drop in the M22 device(s) you need, and wire it. Valued for the robust RMQ-Titan ecosystem and clean look. The trade-off vs. a pre-assembled station is that you populate it yourself (actuator + contacts), so the "green start / 1 NO" a finished station would have is not part of this SKU.
3. Real-World Applications
Building a single-operator surface-mounted control point — e.g. a start button, an E-STOP, a selector, or an indicator — mounted on a machine, wall, or frame where there's no panel to cut into.
4. Technical Specifications
- Type: Empty one-element M22 surface-mounting enclosure (1 × 22 mm hole)
- Contents: enclosure only — no button/contacts included
- Housing: plastic, grey top / black base
- Sealing: IP66
- System: Eaton M22 / RMQ-Titan, 22 mm
- Approvals: UL, CSA, CE
5. Ordering & Compatibility
Order the empty M22-I1 enclosure plus the required M22 actuator (e.g. green start button) and contact/LED blocks separately. Fits standard 22 mm M22 devices. Larger enclosures cover more holes (M22-I2 = 2, M22-I3 = 3, …). For a ready-made green start station, order a complete M22 station SKU instead.
6. Known Issues / DQ
- DQ: this is an empty enclosure (grey/black, IP66), not a populated green start station — the stored green actuator / 1 NO contact were fabricated. Corrected here.
- Practical care: when populating, add an appropriate contact block (and E-STOP where safety requires), match the actuator color/function to the job, and use proper cable entry/glands.
2 sources
Specifikace
|
Certifications
Third-party safety certifications. UL = required for US NEC installations. CE = EU compliance. CSA = Canadian standards.
|
UL, CSA, CE
|
|
Color
Button/actuator color. Green = start/go, Red = stop/emergency, Yellow = caution, Blue = reset (per IEC 60204-1).
|
Grey top / black base
|
|
Contact Configuration
Normally Open — circuit is off until you press. Standard for start/go/enable functions.
|
None — empty enclosure (populate with own M22 actuator + contacts)
|
|
Device type
|
Empty 1-hole M22 surface-mount control station enclosure
|
|
IP Rating
IP66: Dust-tight and withstands powerful water jets from any direction. Standard for outdoor and washdown applications.
|
IP66
|
|
Mounting Type
How the button attaches to the panel. Panel mount is standard — installs through a cutout from the front.
|
Surface mount (enclosed)
|
|
Pn note
|
M22-I1 = empty 1-hole M22 surface enclosure (grey/black, IP66) per RS/Eaton. Stored green start button / 1NO were fabricated (empty box, no button/contacts).
|
|
Pn status
|
empty-enclosure (mislabel-corrected)
|
|
Series
The manufacturer's product family. Products in the same series share mounting systems and accessories.
|
M22
|
Stručný průvodce instalací
Panel cutout: 22mm. Insert from the front of the panel, secure with mounting nut from behind (tighten to 2-3 Nm).
Contact block: Snap or screw the contact block onto the rear of the button body. Ensure the contact block orientation matches the wiring diagram — NO terminals are usually marked.
Wiring: Use 0.5-2.5mm² stranded wire with ferrules. Tighten screw terminals to 0.8 Nm. Test the button function before energizing the circuit.
Rozměry
Schéma zapojení
Řešení problémů
Button doesn't respond when pressed
Check the contact block first — it's the most common failure point. Test continuity across the NO or NC terminals with a multimeter. If no click is felt, the return spring in the head may be broken.
Works intermittently
Contact block contacts are pitted or burned. Replace the contact block — don't try to file the contacts. Check if the rated cycle count has been exceeded.
Button feels mushy or doesn't click
The spring return mechanism in the button head is worn. Replace the head. The contact block can usually be reused if it tests OK.
Kde koupit
Cenové rozpětí
$65.1 — $108.55
u 2 distributorů
Stručné specifikace
- Certifications
- UL, CSA, CE
- Color
- Grey top / black base
- Contact Configuration
- None — empty enclosure (populate with own M22 actuator + contacts)
- Device type
- Empty 1-hole M22 surface-mount control station enclosure
- IP Rating
- IP66
Co říkají uživatelé
“Complete start station: M22 green button in an IP67 sealed enclosure with cable gland. Surface-mount for remote locations. The Eaton equivalent of Schneider XALK.”