Eaton · M22 Series

M22-DL-R

Name: Eaton M22-DL-R
Brand: Eaton
SKU: M22-DL-R

Active

UL UL Listed — meets US safety standards. Required for NEC-inspected installations. CSA CSA Certified — meets Canadian safety standards. Required for installations in Canada. CE CE Marked — complies with EU directives (Low Voltage, Machinery, EMC). ATEX ATEX Certified — approved for potentially explosive atmospheres (gas/dust zones).

M22 Illuminated Red Flush Push Button 24V

Part number: M22 22mm RMQ-Titan series - DL Illuminated flush push button - R Red

Eaton M22 Series Introduced circa 2000

Eaton M22-DL-R — M22 Illuminated Red Flush Push Button 24V

Illuminated red flush push button with integrated 24V LED for Eaton M22 series. 22.5mm cutout, IP67 front.

Common Applications

Illuminated red push button from the Eaton M22 series — the LED lights when the stop circuit is active or a fault condition exists. Commonly found on European-built food processing and packaging machinery where operators need clear visual confirmation that the machine is stopped. The IP67 rating handles high-pressure washdown and oil splashes in food and beverage environments. The 24V LED connects to a PLC output or contactor auxiliary to display machine status. Pairs with the Eaton M22-D-G or an illuminated green M22 variant for a complete start/stop station with visual feedback.

Specifications

Actuator Shape The physical shape of the pressable surface.	Round
Actuator Type The button head style. Flush sits level with the bezel (prevents accidental presses). Extended protrudes for easy access.	Flush
Certifications Third-party safety certifications. UL = required for US NEC installations. CE = EU compliance. CSA = Canadian standards.	UL, CSA, CE, ATEX
Color Button/actuator color. Green = start/go, Red = stop/emergency, Yellow = caution, Blue = reset (per IEC 60204-1).	Red
Contact Configuration Normally Closed — circuit is on until you press. Standard for stop/emergency functions. Wire in series with safety circuits.	1NC
Cutout Diameter The hole size you drill in your panel to mount this button. 22mm is the most common industrial standard worldwide.	22.5mm
Illuminated	Yes
IP Rating IP67: Dust-tight and survives temporary water submersion (1m for 30 min). Handles oil splashes, steam cleaning, and rain.	IP67 (front)
LED Color Color of the built-in LED indicator light.	Red
LED Voltage The voltage required for the built-in LED. Must match your control circuit voltage (typically 24V DC or 230V AC).	24V AC/DC
Material The bezel/body material. Metal bezels are more durable in harsh environments. Plastic is lighter and cheaper.	Plastic/Metal bezel
Mechanical Life How many press cycles before mechanical failure. Higher is better — 10M cycles at 100 presses/day = 274 years.	5,000,000 cycles
Mounting Type How the button attaches to the panel. Panel mount is standard — installs through a cutout from the front.	Panel
Max Operating Temp Highest temperature the button is rated to operate in.	70°C
Min Operating Temp Lowest temperature the button is rated to operate in.	-25°C

Specs with this icon are linked to the manufacturer's original source page

Compatible Alternatives

These products are functionally equivalent cross-references from other manufacturers.

Schneider Electric

ZB4-BW343

Harmony XB4 Illuminated Red Push Button 24V LED

Installation Quick Reference

Panel cutout: 22.5mm. Insert from the front of the panel, secure with mounting nut from behind (tighten to 2-3 Nm).

Contact block: Snap or screw the contact block onto the rear of the button body. Ensure the contact block orientation matches the wiring diagram — NO terminals are usually marked.

Wiring: Use 0.5-2.5mm² stranded wire with ferrules. Tighten screw terminals to 0.8 Nm. Test the button function before energizing the circuit.

Wiring Diagram

Troubleshooting

Button doesn't respond when pressed

Check the contact block first — it's the most common failure point. Test continuity across the NO or NC terminals with a multimeter. If no click is felt, the return spring in the head may be broken.

Works intermittently

Contact block contacts are pitted or burned. Replace the contact block — don't try to file the contacts. Check if the rated cycle count has been exceeded.

Button feels mushy or doesn't click

The spring return mechanism in the button head is worn. Replace the head. The contact block can usually be reused if it tests OK.