3SU1150-1HB20-3CH0
Hoạt độngSIRIUS ACT E-Stop Twist Release 2NC
Siemens SIRIUS ACT e-stop with plastic front ring — budget option.
Ứng Dụng Phổ Biến
Same function as the metal 3SU1150 but with plastic front ring. Costs 40% less. For indoor panels where the premium metal look isnt needed. 2NC contacts for dual-channel safety.
Thông số kỹ thuật
|
Actuator Function
Momentary = springs back when released. Maintained/latching = stays pressed until pressed again.
|
Twist-release
|
|
Actuator Type
The button head style. Flush sits level with the bezel (prevents accidental presses). Extended protrudes for easy access.
|
Mushroom 40mm
|
|
Certifications
Third-party safety certifications. UL = required for US NEC installations. CE = EU compliance. CSA = Canadian standards.
|
UL, CSA, CE
|
|
Color
Button/actuator color. Green = start/go, Red = stop/emergency, Yellow = caution, Blue = reset (per IEC 60204-1).
|
Red
|
|
Contact Configuration
Normally Closed — circuit is on until you press. Standard for stop/emergency functions. Wire in series with safety circuits.
|
2NC
|
|
Cutout Diameter
The hole size you drill in your panel to mount this button. 22mm is the most common industrial standard worldwide.
|
22mm
|
|
IP Rating
IP67: Dust-tight and survives temporary water submersion (1m for 30 min). Handles oil splashes, steam cleaning, and rain.
|
IP67
|
|
Material
The bezel/body material. Metal bezels are more durable in harsh environments. Plastic is lighter and cheaper.
|
Plastic front ring
|
Hướng Dẫn Cài Đặt Nhanh
Panel cutout: 22mm. Mount with the yellow backing plate visible (required by EN/ISO 13850).
Wiring: Wire NC contacts in series with the safety relay input channels. Use dual-channel wiring for SIL 3 / PLe applications. Never wire directly to a motor contactor.
Testing: Press the e-stop and verify the machine stops within the required time. Test the reset mechanism. Repeat monthly per EN/ISO 13850.
Kích thước
Sơ đồ đấu dây
Khắc phục sự cố
E-stop won't reset (twist/pull doesn't release)
Check for debris in the mechanism. For twist-release: turn clockwise 45-90 degrees. For push-pull: pull straight out firmly. If the mechanism is stuck, the internal latch may be damaged — replace the entire head assembly.
Machine doesn't stop when e-stop is pressed
Critical safety issue. Immediately lock out the machine. Check wiring — NC contacts must be in series with the safety relay. Verify the safety relay is functioning. A broken wire in an NC circuit should cause a stop, so check for a wiring bypass.
Safety relay faults after e-stop reset
The safety relay detects a cross-fault between the two monitoring channels. Check that both NC contacts on the e-stop are switching simultaneously. One contact may be welded closed — replace the contact block.
Nơi Mua Hàng
Dải giá
$31.37 — $79.54
từ 2 nhà phân phối
Thông số kỹ thuật nhanh
- Actuator Function
- Twist-release
- Actuator Type
- Mushroom 40mm
- Certifications
- UL, CSA, CE
- Color
- Red
- Contact Configuration
- 2NC
Những Đánh Giá Từ Khách Hàng
“Same function as the metal 3SU1150 but with plastic front ring. Costs 40% less. For indoor panels where the premium metal look isnt needed. 2NC contacts for dual-channel safety.”
