M22-DL-G
ใช้งานอยู่22mm Green Illuminated Flush 24V
Eaton M22 illuminated green flush push button with 24V LED.
การใช้งานทั่วไป
Illuminated start button on Eaton panels. LED lit confirms circuit is active. The M22 LED module accepts 12-30V AC/DC — compatible with most PLC output voltages without an external transformer.
ข้อมูลจำเพาะ
|
Actuator Function
Momentary = springs back when released. Maintained/latching = stays pressed until pressed again.
|
Momentary
|
|
Actuator Type
The button head style. Flush sits level with the bezel (prevents accidental presses). Extended protrudes for easy access.
|
Flush
|
|
Certifications
Third-party safety certifications. UL = required for US NEC installations. CE = EU compliance. CSA = Canadian standards.
|
UL, CSA, CE
|
|
Color
Button/actuator color. Green = start/go, Red = stop/emergency, Yellow = caution, Blue = reset (per IEC 60204-1).
|
Green
|
|
Contact Configuration
Normally Open — circuit is off until you press. Standard for start/go/enable functions.
|
1NO
|
|
Cutout Diameter
The hole size you drill in your panel to mount this button. 22mm is the most common industrial standard worldwide.
|
22.5mm
|
|
Illumination
Whether the button has a built-in light. Illuminated buttons show status (lit = active).
|
Illuminated
|
|
IP Rating
IP67: Dust-tight and survives temporary water submersion (1m for 30 min). Handles oil splashes, steam cleaning, and rain.
|
IP67 (front)
|
|
LED Voltage
The voltage required for the built-in LED. Must match your control circuit voltage (typically 24V DC or 230V AC).
|
24V AC/DC
|
|
Material
The bezel/body material. Metal bezels are more durable in harsh environments. Plastic is lighter and cheaper.
|
Plastic/Metal bezel
|
|
Series
The manufacturer's product family. Products in the same series share mounting systems and accessories.
|
M22
|
คู่มือการติดตั้งอย่างรวดเร็ว
Panel cutout: 22.5mm. Insert from the front of the panel, secure with mounting nut from behind (tighten to 2-3 Nm).
Contact block: Snap or screw the contact block onto the rear of the button body. Ensure the contact block orientation matches the wiring diagram — NO terminals are usually marked.
Wiring: Use 0.5-2.5mm² stranded wire with ferrules. Tighten screw terminals to 0.8 Nm. Test the button function before energizing the circuit.
ขนาด
แผนภาพการเดินสายไฟฟ้า
การแก้ไขปัญหา
Button doesn't respond when pressed
Check the contact block first — it's the most common failure point. Test continuity across the NO or NC terminals with a multimeter. If no click is felt, the return spring in the head may be broken.
Works intermittently
Contact block contacts are pitted or burned. Replace the contact block — don't try to file the contacts. Check if the rated cycle count has been exceeded.
Button feels mushy or doesn't click
The spring return mechanism in the button head is worn. Replace the head. The contact block can usually be reused if it tests OK.
สถานที่จำหน่าย
ช่วงราคา
$17.05 — $32.93
จาก 3 ผู้จัดจำหน่าย
ข้อมูลจำเพาะอย่างย่อ
- Actuator Function
- Momentary
- Actuator Type
- Flush
- Certifications
- UL, CSA, CE
- Color
- Green
- Contact Configuration
- 1NO
สิ่งที่ผู้คนพูดถึง
“Eaton M22-DL-G is a solid choice for push button applications. Standard specs, well-supported.”