MP2-10G
ใช้งานอยู่ABB MP2-10G Green Flush Maintained Pushbutton Head (head-only)
ABB MP2 green guarded push button.
การใช้งานทั่วไป
Guarded green start button. Prevents accidental activation. Used where start buttons are near moving parts.
ข้อมูลจำเพาะ
|
Actuator Function
Momentary = springs back when released. Maintained/latching = stays pressed until pressed again.
|
Maintained (latching) — MP2 = maintained (MP1=momentary)
|
|
Actuator Type
The button head style. Flush sits level with the bezel (prevents accidental presses). Extended protrudes for easy access.
|
Flush
|
|
Certifications
Third-party safety certifications. UL = required for US NEC installations. CE = EU compliance. CSA = Canadian standards.
|
UL, CSA, CE
|
|
Color
Button/actuator color. Green = start/go, Red = stop/emergency, Yellow = caution, Blue = reset (per IEC 60204-1).
|
Green
|
|
Contact Configuration
Normally Open — circuit is off until you press. Standard for start/go/enable functions.
|
None integral (head-only; add ABB MCB contact block + MCBH holder)
|
|
Cutout Diameter
The hole size you drill in your panel to mount this button. 22mm is the most common industrial standard worldwide.
|
22mm
|
|
Device type
|
ABB MP Modular pushbutton HEAD (green flush maintained)
|
|
Pn note
|
Corrected: real code MP2-10G (green FLUSH MAINTAINED head; -GUARD suffix fabricated). ABB MP: MP1 momentary/MP2 maintained/MP3 extended. Head-only (contact separate, cf MP1 #468/469). Stored guarded/1NO/momentary all wrong.
|
|
Pn status
|
corrected (guarded->flush/maintained; -GUARD suffix fabricated)
|
คู่มือการติดตั้งอย่างรวดเร็ว
Panel cutout: 22mm. Insert from the front of the panel, secure with mounting nut from behind (tighten to 2-3 Nm).
Contact block: Snap or screw the contact block onto the rear of the button body. Ensure the contact block orientation matches the wiring diagram — NO terminals are usually marked.
Wiring: Use 0.5-2.5mm² stranded wire with ferrules. Tighten screw terminals to 0.8 Nm. Test the button function before energizing the circuit.
ขนาด
แผนภาพการเดินสายไฟฟ้า
การแก้ไขปัญหา
Button doesn't respond when pressed
Check the contact block first — it's the most common failure point. Test continuity across the NO or NC terminals with a multimeter. If no click is felt, the return spring in the head may be broken.
Works intermittently
Contact block contacts are pitted or burned. Replace the contact block — don't try to file the contacts. Check if the rated cycle count has been exceeded.
Button feels mushy or doesn't click
The spring return mechanism in the button head is worn. Replace the head. The contact block can usually be reused if it tests OK.
สถานที่จำหน่าย
ช่วงราคา
$38.07 — $119.86
จาก 2 ผู้จัดจำหน่าย
ข้อมูลจำเพาะอย่างย่อ
- Actuator Function
- Maintained (latching) — MP2 = maintained (MP1=momentary)
- Actuator Type
- Flush
- Certifications
- UL, CSA, CE
- Color
- Green
- Contact Configuration
- None integral (head-only; add ABB MCB contact block + MCBH holder)
สิ่งที่ผู้คนพูดถึง
“Guarded green start button. Prevents accidental activation. Used where start buttons are near moving parts.”