XACA0661
ActivSchneider Harmony XAC (XACA06) Empty 6-Cutout Pendant Enclosure
Schneider Harmony XACA 6-button pendant control station.
Aplicații frecvente
Schneiders crane pendant competing with Giovenzana PLB. Uses standard XB4/XB5 contact blocks inside. Yellow IP65 housing. 6 momentary buttons for crane bridge and trolley control. Schneider pendants are more common in countries where Schneider dominates the industrial controls market (France, Middle East, Southeast Asia).
Specificații
|
Certifications
Third-party safety certifications. UL = required for US NEC installations. CE = EU compliance. CSA = Canadian standards.
|
CE, UL
|
|
Color
Button/actuator color. Green = start/go, Red = stop/emergency, Yellow = caution, Blue = reset (per IEC 60204-1).
|
Yellow housing
|
|
Contact Configuration
Normally Open — circuit is off until you press. Standard for start/go/enable functions.
|
None — empty enclosure (6 cut-outs for customer 22mm devices; buttons/contacts not included)
|
|
Device type
|
Empty pendant control enclosure (populate with 22mm Harmony devices)
|
|
IP Rating
IP65: Dust-tight and protected against low-pressure water jets. Suitable for indoor industrial and light washdown.
|
IP65
|
|
Material
The bezel/body material. Metal bezels are more durable in harsh environments. Plastic is lighter and cheaper.
|
Polycarbonate
|
|
Pn note
|
XACA06 = empty 6-cutout pendant enclosure (se.com/Mouser/Newark/one-elec: no buttons/contacts). Stored 6x 1NO was fabricated. Exact PN XACA0661 not independently verifiable; verified base part is XACA06.
|
|
Pn status
|
empty-enclosure + pn-unverified
|
Referință rapidă de instalare
Panel cutout: 22mm. Insert from the front of the panel, secure with mounting nut from behind (tighten to 2-3 Nm).
Contact block: Snap or screw the contact block onto the rear of the button body. Ensure the contact block orientation matches the wiring diagram — NO terminals are usually marked.
Wiring: Use 0.5-2.5mm² stranded wire with ferrules. Tighten screw terminals to 0.8 Nm. Test the button function before energizing the circuit.
Dimensiuni
Schemă de cablare
Depanare
Button doesn't respond when pressed
Check the contact block first — it's the most common failure point. Test continuity across the NO or NC terminals with a multimeter. If no click is felt, the return spring in the head may be broken.
Works intermittently
Contact block contacts are pitted or burned. Replace the contact block — don't try to file the contacts. Check if the rated cycle count has been exceeded.
Button feels mushy or doesn't click
The spring return mechanism in the button head is worn. Replace the head. The contact block can usually be reused if it tests OK.
De unde cumpărați
Interval de preț
$18.15 — $164.11
la 2 distribuitori
Specificații rapide
- Certifications
- CE, UL
- Color
- Yellow housing
- Contact Configuration
- None — empty enclosure (6 cut-outs for customer 22mm devices; buttons/contacts not included)
- Device type
- Empty pendant control enclosure (populate with 22mm Harmony devices)
- IP Rating
- IP65
Ce spun utilizatorii
“Schneiders crane pendant competing with Giovenzana PLB. Uses standard XB4/XB5 contact blocks inside. Yellow IP65 housing. 6 momentary buttons for crane bridge and trolley control. Schneider pendants a”
Aflați mai multe
Explicarea gradelor de protecție IP
Ce înseamnă IP65, IP66, IP67, IP69K pentru aplicația dvs.
Ghid 22mm vs 30mm
Ce dimensiune de decupaj în panou aveți nevoie?
Blocuri de contacte: NO vs NC
Cum alegeți și conectați blocurile de contacte
Instrument de căutare butoane
Găsiți butonul potrivit după tip, dimensiune și culoare
