ZEN76
ActiveZooz ZEN76 Z-Wave Plus 700-Series On/Off Switch
Zooz ZEN76 — Z-Wave 800 Series on/off switch.
Common Applications
Z-Wave alternative to Zigbee switches. Z-Wave 800 series chip gives longer range than previous generations. Multi-tap (up to 5) for scene control. Pairs with any Z-Wave controller — Home Assistant, SmartThings, Hubitat. For homes that prefer Z-Wave mesh over Zigbee. Competitively priced against Inovelli.
Research Notes
1. Overview
The Zooz ZEN76 is a Z-Wave Plus (700-series, S2) in-wall on/off paddle switch — a popular, affordable smart switch in the Home Assistant / Z-Wave community. It supports scene control (multi-tap and hold on the paddle), works with any certified Z-Wave hub, and requires a neutral wire (US single-gang box). It's an on/off switch (the dimmer counterpart is the ZEN77). (Data-quality note: ZEN76 is a 700-series (Z-Wave Plus V2, S2) device — not "Z-Wave 800 Long Range" as stored; Zooz's 800LR models are separate revisions.)
2. User Sentiment
Well liked as a reliable, inexpensive Z-Wave switch with genuine scene control and broad hub compatibility (Z-Wave JS / Home Assistant, SmartThings, Hubitat). Praised for value and Zooz's good firmware/support. Common notes: neutral required, it's Z-Wave (needs a Z-Wave controller, not Zigbee/Wi-Fi), and it's an on/off (not dimming) switch — pick ZEN77 for dimming.
3. Real-World Applications
Smart on/off control of hardwired lighting with scene triggers (multi-tap to run automations/scenes) on a Z-Wave network; single-pole or 3-way (with a compatible companion/aux). Common in Home Assistant Z-Wave setups.
4. Technical Specifications
- Type: In-wall Z-Wave Plus on/off paddle switch — 700 series, S2
- Scene control: multi-tap (up to 5×) and hold on the paddle
- Wiring: US single-gang, neutral required; 3-way capable (with aux/companion)
- Ecosystem: any Z-Wave hub — Z-Wave JS / Home Assistant, SmartThings, Hubitat
- Security: S2; Z-Wave Plus V2 (700 series)
- Approvals: UL, FCC
5. Ordering & Compatibility
Requires a Z-Wave controller and a neutral. On/off only — the ZEN77 is the dimmer version; the ZEN73 is a 700-series on/off in a different style. Confirm 3-way wiring needs (Zooz supports direct 3-way with an on/off aux or existing switch). Note Zooz's separate 800LR models if long-range/800-series is specifically required.
6. Known Issues
No notable reliability issues. Practical notes: neutral required, Z-Wave (not Zigbee/Wi-Fi) so needs a Z-Wave hub, on/off only (no dimming), and confirm the correct series (700 here) if 800LR is a requirement.
2 sources
- Zooz 700 Series Z-Wave Plus S2 On/Off Switch ZEN76 — getzooz.com
- Zooz ZEN76 S2 On/Off Switch 700 (Z-Wave Alliance) — z-wavealliance.org
Openness & Hackability
Z-Wave protocol is an open standard (since 2020). Full Home Assistant/Z-Wave JS support. Local-only, no cloud. Multi-tap scene events. OTA firmware updates via Z-Wave JS.
Specifications
|
Certifications
Third-party safety certifications. UL = required for US NEC installations. CE = EU compliance. CSA = Canadian standards.
|
UL, FCC, Z-Wave Plus V2
|
|
Device type
|
In-wall Z-Wave on/off paddle switch (dimmer = ZEN77)
|
|
Smart Home Integrations
Compatible smart home platforms and voice assistants.
|
Home Assistant, SmartThings, Hubitat, Z-Wave JS
|
|
Mounting Type
How the button attaches to the panel. Panel mount is standard — installs through a cutout from the front.
|
US single-gang wall box
|
|
Pn note
|
Corrected: ZEN76 is 700-series (Z-Wave Plus V2, S2), not Z-Wave 800 Long Range. 800LR is a separate Zooz revision.
|
|
Protocol
The wireless communication standard. BLE = short range, phone direct. Zigbee = mesh network, needs hub. Z-Wave = mesh, needs hub. WiFi = direct, higher power.
|
Z-Wave Plus V2 (700 series), S2
|
|
Wiring
|
US single-gang, neutral required; 3-way capable
|
Installation Quick Reference
Panel cutout: 22mm. Insert from the front of the panel, secure with mounting nut from behind (tighten to 2-3 Nm).
Contact block: Snap or screw the contact block onto the rear of the button body. Ensure the contact block orientation matches the wiring diagram — NO terminals are usually marked.
Wiring: Use 0.5-2.5mm² stranded wire with ferrules. Tighten screw terminals to 0.8 Nm. Test the button function before energizing the circuit.
Dimensions
Troubleshooting
Button doesn't respond when pressed
Check the contact block first — it's the most common failure point. Test continuity across the NO or NC terminals with a multimeter. If no click is felt, the return spring in the head may be broken.
Works intermittently
Contact block contacts are pitted or burned. Replace the contact block — don't try to file the contacts. Check if the rated cycle count has been exceeded.
Button feels mushy or doesn't click
The spring return mechanism in the button head is worn. Replace the head. The contact block can usually be reused if it tests OK.
Where to Buy
Price range
$111.96 — $200.39
across 2 sellers in US dollars
Quick Specs
- Certifications
- UL, FCC, Z-Wave Plus V2
- Device type
- In-wall Z-Wave on/off paddle switch (dimmer = ZEN77)
- Smart Home Integrations
- Home Assistant, SmartThings, Hubitat, Z-Wave JS
- Mounting Type
- US single-gang wall box
- Pn note
- Corrected: ZEN76 is 700-series (Z-Wave Plus V2, S2), not Z-Wave 800 Long Range. 800LR is a separate Zooz revision.
What People Are Saying
“Z-Wave protocol is an open standard (since 2020). Full Home Assistant/Z-Wave JS support. Local-only, no cloud. Multi-tap scene events. OTA firmware updates via Z-Wave JS.”