ZEN76
AktivníZooz ZEN76 Z-Wave Plus 700-Series On/Off Switch
Zooz ZEN76 — Z-Wave 800 Series on/off switch.
Běžné aplikace
Z-Wave alternative to Zigbee switches. Z-Wave 800 series chip gives longer range than previous generations. Multi-tap (up to 5) for scene control. Pairs with any Z-Wave controller — Home Assistant, SmartThings, Hubitat. For homes that prefer Z-Wave mesh over Zigbee. Competitively priced against Inovelli.
Otevřenost a modifikovatelnost
Z-Wave protocol is an open standard (since 2020). Full Home Assistant/Z-Wave JS support. Local-only, no cloud. Multi-tap scene events. OTA firmware updates via Z-Wave JS.
Specifikace
|
Certifications
Third-party safety certifications. UL = required for US NEC installations. CE = EU compliance. CSA = Canadian standards.
|
UL, FCC, Z-Wave Plus V2
|
|
Device type
|
In-wall Z-Wave on/off paddle switch (dimmer = ZEN77)
|
|
Smart Home Integrations
Compatible smart home platforms and voice assistants.
|
Home Assistant, SmartThings, Hubitat, Z-Wave JS
|
|
Mounting Type
How the button attaches to the panel. Panel mount is standard — installs through a cutout from the front.
|
US single-gang wall box
|
|
Pn note
|
Corrected: ZEN76 is 700-series (Z-Wave Plus V2, S2), not Z-Wave 800 Long Range. 800LR is a separate Zooz revision.
|
|
Protocol
The wireless communication standard. BLE = short range, phone direct. Zigbee = mesh network, needs hub. Z-Wave = mesh, needs hub. WiFi = direct, higher power.
|
Z-Wave Plus V2 (700 series), S2
|
|
Wiring
|
US single-gang, neutral required; 3-way capable
|
Stručný průvodce instalací
Panel cutout: 22mm. Insert from the front of the panel, secure with mounting nut from behind (tighten to 2-3 Nm).
Contact block: Snap or screw the contact block onto the rear of the button body. Ensure the contact block orientation matches the wiring diagram — NO terminals are usually marked.
Wiring: Use 0.5-2.5mm² stranded wire with ferrules. Tighten screw terminals to 0.8 Nm. Test the button function before energizing the circuit.
Rozměry
Řešení problémů
Button doesn't respond when pressed
Check the contact block first — it's the most common failure point. Test continuity across the NO or NC terminals with a multimeter. If no click is felt, the return spring in the head may be broken.
Works intermittently
Contact block contacts are pitted or burned. Replace the contact block — don't try to file the contacts. Check if the rated cycle count has been exceeded.
Button feels mushy or doesn't click
The spring return mechanism in the button head is worn. Replace the head. The contact block can usually be reused if it tests OK.
Kde koupit
Cenové rozpětí
$111.96 — $200.39
u 2 distributorů
Stručné specifikace
- Certifications
- UL, FCC, Z-Wave Plus V2
- Device type
- In-wall Z-Wave on/off paddle switch (dimmer = ZEN77)
- Smart Home Integrations
- Home Assistant, SmartThings, Hubitat, Z-Wave JS
- Mounting Type
- US single-gang wall box
- Pn note
- Corrected: ZEN76 is 700-series (Z-Wave Plus V2, S2), not Z-Wave 800 Long Range. 800LR is a separate Zooz revision.
Co říkají uživatelé
“Z-Wave protocol is an open standard (since 2020). Full Home Assistant/Z-Wave JS support. Local-only, no cloud. Multi-tap scene events. OTA firmware updates via Z-Wave JS.”