MP3-10R
Active22mm Red Extended Pushbutton Head (ABB Modular)
ABB modular red extended push button.
Common Applications
Extended red stop button for ABB panels. Raised profile for accessibility.
Research Notes
1. Overview
The ABB MP3-10R (order code 1SFA611102R1001) is a Modular-series pushbutton head/operator: 22.5 mm, extended (raised) button, momentary action, non-illuminated, red operator with a black plastic bezel/housing. It is part of ABB's non-metallic Modular range (MP1 = flush, MP3 = extended, MPM = mushroom). Like the rest of the range it is a head only — a contact block plus a contact-block holder (MCBH) must be added separately to make a working device; the head itself has no integral switching.
2. User Sentiment
As an industrial control component it has little consumer sentiment. The ABB Modular line is valued for low cost, light weight (plastic housing), and the mix-and-match contact system. The extended head is chosen for easy/gloved actuation and higher visibility, accepting a marginally higher accidental-press risk than the flush MP1.
3. Real-World Applications
Machine control panels, control/pendant stations, and OEM equipment where a raised red momentary control button is needed. (A raised red momentary is a control button, not a latching E-stop — ABB's mushroom/E-stop actuators are a different code.)
4. Technical Specifications
- Type: Modular extended momentary pushbutton head (operator only)
- Color / bezel: Red button, black plastic bezel/housing
- Size: 22.5 mm cutout
- Contact: none integral — add ABB Modular contact block + holder (MCB-10 = 1NO, MCB-01 = 1NC), via MCBH holder
- Sealing: IP66 (front) / IP20 (terminals); NEMA 1/3R/4/4X/12/13
- Operating temp: -25 to +70 °C
- Approvals: UL, CSA, CE, RoHS
5. Ordering & Compatibility
Order the head plus a contact-block holder and the required MCB contact blocks (or buy a pre-built assembly). Interchangeable within the ABB Modular ecosystem (holders, legend plates, guards). Stocked by ABB, Amazon, Platt, Anixter, Allied, and general distributors.
6. Known Issues
No notable reliability issues; a mature modular design. The recurring buying pitfall is modular — a bare MP3-10R head does nothing until a contact block + holder are added.
4 sources
- MP3-10R | ABB Modular Pushbutton — new.abb.com
- ABB MP3-10R Modular Series Red Push Button Head Momentary 22mm — alliedelec.com
- ABB MP3-10R Extended Pushbutton 22mm — platt.com
- MP3-10R ABB Modular Pushbutton — anixter.com
Specifications
|
Actuator Type
The button head style. Flush sits level with the bezel (prevents accidental presses). Extended protrudes for easy access.
|
Extended
|
|
Bezel
The ring around the button face. Chrome/silver for standard use, black for stealth panels.
|
Black plastic
|
|
Certifications
Third-party safety certifications. UL = required for US NEC installations. CE = EU compliance. CSA = Canadian standards.
|
UL, CSA, CE
|
|
Color
Button/actuator color. Green = start/go, Red = stop/emergency, Yellow = caution, Blue = reset (per IEC 60204-1).
|
Red
|
|
Component type
|
Head/operator only (contact block + MCBH holder separate)
|
|
Contact Configuration
1NO + 1NC: One circuit closes and one opens when pressed. Common for start buttons that also signal 'running' state.
|
None integral — add MCB-10 (1NO)/MCB-01 (1NC) via MCBH holder
|
|
Cutout Diameter
The hole size you drill in your panel to mount this button. 22mm is the most common industrial standard worldwide.
|
22mm
|
|
IP Rating
IP66: Dust-tight and withstands powerful water jets from any direction. Standard for outdoor and washdown applications.
|
IP66 (front) / IP20 (terminals); NEMA 1/3R/4/4X/12/13
|
|
Operating temp
|
-25 to +70 C
|
Installation Quick Reference
Panel cutout: 22mm. Insert from the front of the panel, secure with mounting nut from behind (tighten to 2-3 Nm).
Contact block: Snap or screw the contact block onto the rear of the button body. Ensure the contact block orientation matches the wiring diagram — NO terminals are usually marked.
Wiring: Use 0.5-2.5mm² stranded wire with ferrules. Tighten screw terminals to 0.8 Nm. Test the button function before energizing the circuit.
Dimensions
Wiring Diagram
Troubleshooting
Button doesn't respond when pressed
Check the contact block first — it's the most common failure point. Test continuity across the NO or NC terminals with a multimeter. If no click is felt, the return spring in the head may be broken.
Works intermittently
Contact block contacts are pitted or burned. Replace the contact block — don't try to file the contacts. Check if the rated cycle count has been exceeded.
Button feels mushy or doesn't click
The spring return mechanism in the button head is worn. Replace the head. The contact block can usually be reused if it tests OK.
Where to Buy
Price range
$63.59 — $95.07
across 2 sellers in US dollars
Quick Specs
- Actuator Type
- Extended
- Bezel
- Black plastic
- Certifications
- UL, CSA, CE
- Color
- Red
- Component type
- Head/operator only (contact block + MCBH holder separate)
What People Are Saying
“Extended red stop button for ABB panels. Raised profile for accessibility.”