M22-DL-G-K10-24
AktywnyM22 Complete Green Illuminated 24V 1NO
Eaton M22 complete illuminated green start with contact.
Typowe Zastosowania
The ultimate convenience part — illuminated green button with 24V LED and 1NO contact, fully pre-assembled. One Eaton part number replaces 3-4 separate components. Saves 5 minutes assembly time per button on large panel builds.
Research Notes
1. Overview
The Eaton M22-DL-G-K10-24 is a complete illuminated pushbutton in the Eaton M22 / RMQ-Titan 22.5 mm modular system — bundled as a single order number that includes the green flush illuminated actuator (M22-DL-G), a 1 NO contact block (K10), and a 24 V LED element (-24). It's momentary (spring-return), IP67 front, UL/CSA/CE. Because it's a Complete Device, the contact (1 NO) and LED voltage (24 V) are genuinely part of this catalog number — unlike Eaton's head-only M22-D… codes, where contacts and LEDs are ordered separately.
2. User Sentiment
The M22/RMQ-Titan line is a professional favorite for its clean modular design and robust build; ordering it as a complete device saves the effort of separately specifying actuator + LED + contact, which reduces BOM mistakes. The usual notes: match LED voltage (24 V here), confirm the 22.5 mm cutout, and remember that for field service the pieces (lens/actuator, LED, contact) are individually replaceable.
3. Real-World Applications
Illuminated START/RUN/ON pushbutton on machinery and control panels; the integral 24 V LED indicates energized/active state, and the 1 NO contact drives a contactor/PLC input. Green = start/on by convention.
4. Technical Specifications
- Type: M22/RMQ-Titan complete illuminated pushbutton, 22.5 mm
- Actuator: flush, momentary; green, illuminated
- Contact: 1 NO (K10 block)
- Illumination: LED, 24 V AC/DC (-24)
- Cutout: 22.5 mm
- Sealing: IP67 (front); typically IP69K on M22
- Approvals: UL, CSA, CE
5. Ordering & Compatibility
Complete device — no need to separately order actuator/LED/contact. Fits 22.5 mm cutouts. Confirm 24 V LED supply. Service parts are the standard M22 modular pieces (actuator/lens M22-DL-G, LED element, K10 contact). Related complete codes vary by color/contact/voltage (e.g. K01 = 1 NC, other voltages).
6. Known Issues
No notable reliability issues — mainstream M22 hardware. Practical care: match the LED voltage (24 V, not 120/230 V), confirm the 22.5 mm cutout, and note this is a complete unit (contrast the head-only M22-D… codes where contact/LED are separate — a common source of spec confusion).
2 sources
- Eaton M22-DL-G-K10-24 complete illuminated green pushbutton — eaton.com
- Eaton M22 complete illuminated green pushbutton, 1NO — automation24.com
Specyfikacje
|
Certifications
Third-party safety certifications. UL = required for US NEC installations. CE = EU compliance. CSA = Canadian standards.
|
UL, CSA, CE
|
|
Color
Button/actuator color. Green = start/go, Red = stop/emergency, Yellow = caution, Blue = reset (per IEC 60204-1).
|
Green
|
|
Contact Configuration
Normally Open — circuit is off until you press. Standard for start/go/enable functions.
|
1NO
|
|
Cutout Diameter
The hole size you drill in your panel to mount this button. 22mm is the most common industrial standard worldwide.
|
22.5mm
|
|
Device type
|
Complete device (actuator+K10 1NO contact+24V LED bundled; not head-only)
|
|
Illumination
Whether the button has a built-in light. Illuminated buttons show status (lit = active).
|
Illuminated
|
|
IP Rating
IP69K: Dust-tight and withstands high-pressure, high-temperature steam jets. Built for food processing washdown environments.
|
IP67 (front); IP69K typical on M22
|
|
LED Voltage
The voltage required for the built-in LED. Must match your control circuit voltage (typically 24V DC or 230V AC).
|
24V AC/DC
|
|
Series
The manufacturer's product family. Products in the same series share mounting systems and accessories.
|
M22
|
Skrócona Instrukcja Montażu
Panel cutout: 22.5mm. Insert from the front of the panel, secure with mounting nut from behind (tighten to 2-3 Nm).
Contact block: Snap or screw the contact block onto the rear of the button body. Ensure the contact block orientation matches the wiring diagram — NO terminals are usually marked.
Wiring: Use 0.5-2.5mm² stranded wire with ferrules. Tighten screw terminals to 0.8 Nm. Test the button function before energizing the circuit.
Wymiary
Schemat Połączeń
Rozwiązywanie Problemów
Button doesn't respond when pressed
Check the contact block first — it's the most common failure point. Test continuity across the NO or NC terminals with a multimeter. If no click is felt, the return spring in the head may be broken.
Works intermittently
Contact block contacts are pitted or burned. Replace the contact block — don't try to file the contacts. Check if the rated cycle count has been exceeded.
Button feels mushy or doesn't click
The spring return mechanism in the button head is worn. Replace the head. The contact block can usually be reused if it tests OK.
Gdzie Kupić
Przedział cenowy
$31.92 — $152.73
u 2 dystrybutorów
Skrócone Specyfikacje
- Certifications
- UL, CSA, CE
- Color
- Green
- Contact Configuration
- 1NO
- Cutout Diameter
- 22.5mm
- Device type
- Complete device (actuator+K10 1NO contact+24V LED bundled; not head-only)
Co Mówią Użytkownicy
“The ultimate convenience part — illuminated green button with 24V LED and 1NO contact, fully pre-assembled. One Eaton part number replaces 3-4 separate components. Saves 5 minutes assembly time per bu”
Dowiedz się Więcej
Objaśnienie Klasyfikacji IP
Co oznaczają IP65, IP66, IP67, IP69K dla Państwa zastosowania
Przewodnik 22mm vs 30mm
Jakiego rozmiaru otworu montażowego potrzebujesz?
Bloki Styków: NO vs NC
Jak wybrać i podłączyć bloki styków
Narzędzie Wyszukiwania Przycisków
Znajdź właściwy przycisk wg typu, rozmiaru i koloru