MP1-10K
AktywnyABB MP1-10K Modular Black Flush Pushbutton Head (head-only)
ABB black flush push button.
Typowe Zastosowania
Black for auxiliary functions. Counter reset, horn silence, lamp test.
Specyfikacje
|
Actuator Type
The button head style. Flush sits level with the bezel (prevents accidental presses). Extended protrudes for easy access.
|
Flush
|
|
Certifications
Third-party safety certifications. UL = required for US NEC installations. CE = EU compliance. CSA = Canadian standards.
|
UL, CSA, CE
|
|
Color
Button/actuator color. Green = start/go, Red = stop/emergency, Yellow = caution, Blue = reset (per IEC 60204-1).
|
Black
|
|
Contact Configuration
Normally Open — circuit is off until you press. Standard for start/go/enable functions.
|
None integral (head-only; add ABB MCB contact block + MCBH holder)
|
|
Cutout Diameter
The hole size you drill in your panel to mount this button. 22mm is the most common industrial standard worldwide.
|
22mm
|
|
Device type
|
ABB MP Modular pushbutton HEAD (non-illuminated, black flush)
|
|
Pn note
|
MP series is head-only (MCB block + MCBH holder separate); stored 1NO misattributed (cf MP1-10W #468, MP3 #357/358). Also: ABB color code K is non-standard — black = MP1-10B; verify exact code.
|
|
Pn status
|
head-only-corrected + color-code-to-verify
|
Skrócona Instrukcja Montażu
Panel cutout: 22mm. Insert from the front of the panel, secure with mounting nut from behind (tighten to 2-3 Nm).
Contact block: Snap or screw the contact block onto the rear of the button body. Ensure the contact block orientation matches the wiring diagram — NO terminals are usually marked.
Wiring: Use 0.5-2.5mm² stranded wire with ferrules. Tighten screw terminals to 0.8 Nm. Test the button function before energizing the circuit.
Wymiary
Schemat Połączeń
Rozwiązywanie Problemów
Button doesn't respond when pressed
Check the contact block first — it's the most common failure point. Test continuity across the NO or NC terminals with a multimeter. If no click is felt, the return spring in the head may be broken.
Works intermittently
Contact block contacts are pitted or burned. Replace the contact block — don't try to file the contacts. Check if the rated cycle count has been exceeded.
Button feels mushy or doesn't click
The spring return mechanism in the button head is worn. Replace the head. The contact block can usually be reused if it tests OK.
Gdzie Kupić
Przedział cenowy
$16.21 — $25.14
u 2 dystrybutorów
Skrócone Specyfikacje
- Actuator Type
- Flush
- Certifications
- UL, CSA, CE
- Color
- Black
- Contact Configuration
- None integral (head-only; add ABB MCB contact block + MCBH holder)
- Cutout Diameter
- 22mm
Co Mówią Użytkownicy
“Black for auxiliary functions. Counter reset, horn silence, lamp test.”
Dowiedz się Więcej
Objaśnienie Klasyfikacji IP
Co oznaczają IP65, IP66, IP67, IP69K dla Państwa zastosowania
Przewodnik 22mm vs 30mm
Jakiego rozmiaru otworu montażowego potrzebujesz?
Bloki Styków: NO vs NC
Jak wybrać i podłączyć bloki styków
Narzędzie Wyszukiwania Przycisków
Znajdź właściwy przycisk wg typu, rozmiaru i koloru