M22-DRL-G
현행 제품ATEX Illuminated Green Push Button 24V
Eaton M22 ATEX-certified illuminated green push button.
일반적인 용도
Start button on ATEX-certified motor starters in refineries and chemical plants. The illuminated LED confirms the circuit is active — critical in noisy environments where audible feedback is insufficient. Zone 2 rating covers most general refinery areas.
사양 목록
|
Actuator Type
The button head style. Flush sits level with the bezel (prevents accidental presses). Extended protrudes for easy access.
|
Flush
|
|
ATEX Zone
The hazardous area classification. Zone 1 = gas likely present. Zone 2 = gas unlikely. Zone 21/22 = combustible dust.
|
Zone 2, Zone 22
|
|
Certifications
Third-party safety certifications. UL = required for US NEC installations. CE = EU compliance. CSA = Canadian standards.
|
ATEX, IECEx, CE
|
|
Color
Button/actuator color. Green = start/go, Red = stop/emergency, Yellow = caution, Blue = reset (per IEC 60204-1).
|
Green
|
|
Contact Configuration
Normally Open — circuit is off until you press. Standard for start/go/enable functions.
|
1NO
|
|
Cutout Diameter
The hole size you drill in your panel to mount this button. 22mm is the most common industrial standard worldwide.
|
22.5mm
|
|
Explosion Group
The gas group the device is certified for. IIC covers hydrogen (most restrictive). IIB covers ethylene. IIA covers propane.
|
IIC
|
|
Illumination
Whether the button has a built-in light. Illuminated buttons show status (lit = active).
|
Illuminated
|
|
IP Rating
IP67: Dust-tight and survives temporary water submersion (1m for 30 min). Handles oil splashes, steam cleaning, and rain.
|
IP67
|
|
LED Voltage
The voltage required for the built-in LED. Must match your control circuit voltage (typically 24V DC or 230V AC).
|
24V DC
|
|
Temperature Class
Maximum surface temperature. T6 (85°C) is most restrictive. T1 (450°C) is least. Must not exceed auto-ignition temp of the gas.
|
T4
|
이 아이콘이 있는 사양은 제조사의 원본 출처 페이지에 연결되어 있습니다
설치 빠른 참조
Panel cutout: 22.5mm. Insert from the front of the panel, secure with mounting nut from behind (tighten to 2-3 Nm).
Contact block: Snap or screw the contact block onto the rear of the button body. Ensure the contact block orientation matches the wiring diagram — NO terminals are usually marked.
Wiring: Use 0.5-2.5mm² stranded wire with ferrules. Tighten screw terminals to 0.8 Nm. Test the button function before energizing the circuit.
외형 치수
배선도
문제 해결
Button doesn't respond when pressed
Check the contact block first — it's the most common failure point. Test continuity across the NO or NC terminals with a multimeter. If no click is felt, the return spring in the head may be broken.
Works intermittently
Contact block contacts are pitted or burned. Replace the contact block — don't try to file the contacts. Check if the rated cycle count has been exceeded.
Button feels mushy or doesn't click
The spring return mechanism in the button head is worn. Replace the head. The contact block can usually be reused if it tests OK.
구매처
가격 범위
$14.84 — $26.69
4개 대리점
주요 사양
- Actuator Type
- Flush
- ATEX Zone
- Zone 2, Zone 22
- Certifications
- ATEX, IECEx, CE
- Color
- Green
- Contact Configuration
- 1NO
사용자 후기
“Solid button for panel builds. Eaton M22 ATEX series is well-proven in the field. Standard 22mm mounting means easy replacement if needed.”
자세히 보기
데이터 출처
사양 및 제품 데이터는 다음 참고 자료에서 수집되었습니다.