800T-FXP16RA1
현행 제품Bulletin 800T 30.5mm Red Illuminated Mushroom Push-Pull E-Stop (1NCLB+1NO)
Red illuminated 40mm mushroom-head push-pull e-stop for the Allen-Bradley 800T 30.5mm NEMA system. 120V AC lamp, 1 normally closed late-break and 1 normally open contact. Metal construction.
일반적인 용도
Found on heavy industrial machinery as an emergency stop. The push-pull mechanism latches in the pushed (off) position and requires deliberate pulling to reset — preventing accidental restart. The 120V illumination makes it visible even in dim conditions. The late-break NC contact ensures the stop signal is maintained until the actuator fully releases. NEMA 4/13 metal body suits oily, dusty plant floors.
사양 목록
|
Actuator Type
The button head style. Flush sits level with the bezel (prevents accidental presses). Extended protrudes for easy access.
|
Mushroom Head (40mm)
|
|
Certifications
Third-party safety certifications. UL = required for US NEC installations. CE = EU compliance. CSA = Canadian standards.
|
UL, CSA, CE, CCC
|
|
Color
Button/actuator color. Green = start/go, Red = stop/emergency, Yellow = caution, Blue = reset (per IEC 60204-1).
|
Red
|
|
Contact Configuration
1NO + 1NC: One circuit closes and one opens when pressed. Common for start buttons that also signal 'running' state.
|
1NCLB + 1NO
|
|
Cutout Diameter
The hole size you drill in your panel to mount this button. 22mm is the most common industrial standard worldwide.
|
30.5mm
|
|
Illumination
Whether the button has a built-in light. Illuminated buttons show status (lit = active).
|
120V AC
|
|
Material
The bezel/body material. Metal bezels are more durable in harsh environments. Plastic is lighter and cheaper.
|
Metal
|
|
Mounting Type
How the button attaches to the panel. Panel mount is standard — installs through a cutout from the front.
|
Panel (30.5mm cutout)
|
|
Reset type
|
Push-Pull (maintained)
|
|
Terminal Type
How you connect wires. Screw clamp is most common in industrial. Spring cage is faster but requires proper ferrules.
|
Screw
|
|
Max Voltage
|
600V AC/DC
|
설치 빠른 참조
Panel cutout: 30.5mm. Mount with the yellow backing plate visible (required by EN/ISO 13850).
Wiring: Wire NC contacts in series with the safety relay input channels. Use dual-channel wiring for SIL 3 / PLe applications. Never wire directly to a motor contactor.
Testing: Press the e-stop and verify the machine stops within the required time. Test the reset mechanism. Repeat monthly per EN/ISO 13850.
외형 치수
배선도
문제 해결
E-stop won't reset (twist/pull doesn't release)
Check for debris in the mechanism. For twist-release: turn clockwise 45-90 degrees. For push-pull: pull straight out firmly. If the mechanism is stuck, the internal latch may be damaged — replace the entire head assembly.
Machine doesn't stop when e-stop is pressed
Critical safety issue. Immediately lock out the machine. Check wiring — NC contacts must be in series with the safety relay. Verify the safety relay is functioning. A broken wire in an NC circuit should cause a stop, so check for a wiring bypass.
Safety relay faults after e-stop reset
The safety relay detects a cross-fault between the two monitoring channels. Check that both NC contacts on the e-stop are switching simultaneously. One contact may be welded closed — replace the contact block.
주요 사양
- Actuator Type
- Mushroom Head (40mm)
- Certifications
- UL, CSA, CE, CCC
- Color
- Red
- Contact Configuration
- 1NCLB + 1NO
- Cutout Diameter
- 30.5mm
사용자 후기
“Solid Allen-Bradley product, widely available and well-documented.”