ABB · CP Seeria

1SFA619100R1142

Aktiivne
UL CSA CE

ABB CP1 Complete Red Button 1NC

Tootenumber: 1 - 100R
ABB CP Seeria Introduced circa 2015

ABB CP series complete red push button.

Tüüpilised rakendused

Complete red stop button in ABBs compact CP format. Same 22mm mounting, slimmer profile. One part number for the entire assembly.

Research Notes

1. What this is

1SFA619100R1142 is an ABB order code from the CP compact pushbutton family, but its exact identity could not be confirmed — sources conflict and ABB/TME's own pages were unreachable during research. Treat the specifics below as unverified until confirmed against ABB's catalog.

2. Why it's uncertain

  • The stored designation "CP1-10R-02" is internally contradictory: ABB's trailing digits are the contact code, where -02 = 2 NC but the stored contact is 1 NC (which would be -01).
  • A distributor (Alibaba) lists this exact PN as "CP1-11G-01" (green), contradicting the stored red.
  • ABB's own product page and TME timed out / 403'd during automated lookup, so no authoritative decode was obtained.

3. What's most likely

It is an ABB CP-series compact 22 mm pushbutton, probably red (the most-supported color), with a 1 NC or 2 NC contact — but the exact type code (CP1-10R-01 vs -02 vs the Alibaba "CP1-11G-01") is unresolved. Do not rely on the color/contact here without checking ABB's catalog for 1SFA619100R1142.

4. Why this page exists (data-quality)

Kept and flagged pn_status: needs-verification rather than asserting a possibly-wrong decode. If you can confirm the color/contact from ABB's official catalog, this entry can be corrected. (Compare the verified ABB CP1 entries in this catalog: CP1-10G-11 = 1SFA619100R1072, CP1-20G-11 = 1SFA619100R2072.)


2 sources
  1. ABB 1SFA619100R1142 (identity to verify) — new.abb.com
  2. ABB CP Compact pushbutton range (naming reference) — new.abb.com

Spetsifikatsioonid

Actuator Type
Flush
Certifications
UL, CSA, CE
Color
Red
Contact Configuration
1NC
Cutout Diameter
22mm
IP Rating
IP66
Mouser checked
2026-09-28
Mouser matched
false
Pn note
PN decode unresolved: stored type CP1-10R-02 contradicts stored contact 1NC (-02 = 2NC; 1NC = -01). ABB/TME pages unreachable; Alibaba lists this PN as CP1-11G-01 (green). Color(red) likely correct but contact/type code need an authoritative ABB catalog check.
Pn status
needs-verification

Paigalduse kiirjuhend

Panel cutout: 22mm. Insert from the front of the panel, secure with mounting nut from behind (tighten to 2-3 Nm).

Contact block: Snap or screw the contact block onto the rear of the button body. Ensure the contact block orientation matches the wiring diagram — NO terminals are usually marked.

Wiring: Use 0.5-2.5mm² stranded wire with ferrules. Tighten screw terminals to 0.8 Nm. Test the button function before energizing the circuit.

Mõõtmed

Front 22mm cutout panel hole diameter Side panel contact ~45mm depth

Ühenduseskeem

L T 21 22 NC (closed) opens on press

Veaotsing

Button doesn't respond when pressed

Check the contact block first — it's the most common failure point. Test continuity across the NO or NC terminals with a multimeter. If no click is felt, the return spring in the head may be broken.

Works intermittently

Contact block contacts are pitted or burned. Replace the contact block — don't try to file the contacts. Check if the rated cycle count has been exceeded.

Button feels mushy or doesn't click

The spring return mechanism in the button head is worn. Replace the head. The contact block can usually be reused if it tests OK.

Kust osta

Hinnavahemik

$24.72 — $76.7

2 edasimüüja juures

Kiirspetsifikatsioonid

Actuator Type
Flush
Certifications
UL, CSA, CE
Color
Red
Contact Configuration
1NC
Cutout Diameter
22mm

Mida kasutajad ütlevad

+

“Complete red stop button in ABBs compact CP format. Same 22mm mounting, slimmer profile. One part number for the entire assembly.”

Reddit r/PLC 31 poolthääli Vaata arutelu →