ZB4-BP2
AktivSchneider ZB4BP2 Black Projecting Pushbutton Head (Harmony XB4)
Schneider XB4 red guarded (shrouded) push button.
Typische Anwendungen
Guarded button with a raised ring around the actuator that prevents accidental presses. Used for stop buttons near moving machinery where operators might lean against the panel. The guard forces deliberate pressing — you have to reach over the ring to press the button. Also used for critical functions where accidental activation would be costly.
Spezifikationen
|
Actuator Function
Momentary = springs back when released. Maintained/latching = stays pressed until pressed again.
|
Momentary
|
|
Actuator Type
The button head style. Flush sits level with the bezel (prevents accidental presses). Extended protrudes for easy access.
|
Projecting (raised, ~Ø29.5mm cap)
|
|
Certifications
Third-party safety certifications. UL = required for US NEC installations. CE = EU compliance. CSA = Canadian standards.
|
UL, CSA, CE
|
|
Color
Button/actuator color. Green = start/go, Red = stop/emergency, Yellow = caution, Blue = reset (per IEC 60204-1).
|
Black
|
|
Contact Configuration
Normally Open — circuit is off until you press. Standard for start/go/enable functions.
|
None integral (head-only; add ZB4 contact block)
|
|
Cutout Diameter
The hole size you drill in your panel to mount this button. 22mm is the most common industrial standard worldwide.
|
22mm
|
|
Device type
|
ZB4 HEAD only (non-illuminated black projecting, momentary); complete unit = XB4-BP2
|
|
IP Rating
IP66: Dust-tight and withstands powerful water jets from any direction. Standard for outdoor and washdown applications.
|
IP66
|
|
Material
The bezel/body material. Metal bezels are more durable in harsh environments. Plastic is lighter and cheaper.
|
Metal
|
|
Pn note
|
Corrected: ZB4BP2 = BLACK PROJECTING pushbutton head (se.com datasheet: black projecting Ø22 spring return), not red/guarded. Color 2=black; BP=projecting actuator.
|
Installationskurzanleitung
Panel cutout: 22mm. Insert from the front of the panel, secure with mounting nut from behind (tighten to 2-3 Nm).
Contact block: Snap or screw the contact block onto the rear of the button body. Ensure the contact block orientation matches the wiring diagram — NO terminals are usually marked.
Wiring: Use 0.5-2.5mm² stranded wire with ferrules. Tighten screw terminals to 0.8 Nm. Test the button function before energizing the circuit.
Abmessungen
Schaltplan
Fehlerbehebung
Button doesn't respond when pressed
Check the contact block first — it's the most common failure point. Test continuity across the NO or NC terminals with a multimeter. If no click is felt, the return spring in the head may be broken.
Works intermittently
Contact block contacts are pitted or burned. Replace the contact block — don't try to file the contacts. Check if the rated cycle count has been exceeded.
Button feels mushy or doesn't click
The spring return mechanism in the button head is worn. Replace the head. The contact block can usually be reused if it tests OK.
Bezugsquellen
Preisbereich
$21.24 — $73.99
bei 3 Händlern
Kurzspezifikationen
- Actuator Function
- Momentary
- Actuator Type
- Projecting (raised, ~Ø29.5mm cap)
- Certifications
- UL, CSA, CE
- Color
- Black
- Contact Configuration
- None integral (head-only; add ZB4 contact block)
Das sagen Anwender
“Guarded button with a raised ring around the actuator that prevents accidental presses. Used for stop buttons near moving machinery where operators might lean against the panel. The guard forces delib”
