ESP32-C3-MINI
ActiveESP32-C3 WiFi/BLE Smart Button Module
Espressif ESP32-C3 — the chip inside thousands of DIY smart buttons.
Common Applications
Not a button itself — the brain inside DIY smart buttons. Run ESPHome firmware and connect any physical button to create a custom WiFi or BLE smart button. Under $3 per module. Powers the maker/DIY smart home movement. More customizable than Zigbee buttons but requires programming. Found in custom home automation, art installations, and escape rooms.
Research Notes
1. Overview
The ESP32-C3-MINI-1 is a compact Espressif surface-mount module built on the ESP32-C3 single-core 32-bit RISC-V SoC (up to 160 MHz) with integrated Wi-Fi (2.4 GHz 802.11 b/g/n) and Bluetooth LE 5.0. It is not a finished button — it's the radio+MCU brains you build a DIY smart button around: wire a tactile/momentary switch to a GPIO, flash firmware (ESPHome, Arduino, or ESP-IDF), and it becomes a local Wi-Fi/BLE button that publishes press events to Home Assistant/MQTT. Variants: -1 (PCB antenna), -1U (external u.FL antenna).
2. User Sentiment
Extremely popular with makers for its low cost, RISC-V core, generous GPIO, and first-class ESPHome/Home Assistant support. Builders like that a $1–3 module yields a fully local, cloud-free button/remote with battery-friendly deep-sleep. Caveats raised: it's a bare module (needs a carrier PCB, power, and antenna clearance), single-core (less headroom than the ESP32-S3), and RF layout matters for range.
3. Real-World Applications
DIY smart buttons, scene controllers, and wireless remotes; sensor nodes; Matter-over-Wi-Fi accessories (ESP32-C3 supports Matter). Common in ESPHome "wake-on-press, deep-sleep" button builds that report to Home Assistant with no vendor cloud.
4. Technical Specifications
- Type: Wi-Fi + BLE SoC module (DIY smart-button platform) — not a standalone button
- MCU: ESP32-C3 single-core RISC-V, up to 160 MHz; 400 KB SRAM; on-module flash (e.g. 4 MB, ESP32-C3FH4)
- Radio: Wi-Fi 2.4 GHz 802.11 b/g/n; Bluetooth LE 5.0 (LE, mesh, long-range)
- I/O: multiple GPIO, ADC, UART/SPI/I²C, PWM; deep-sleep low-power modes
- Temp: −40 to +105 °C
- Antenna: PCB (-1) or external u.FL (-1U)
- Toolchains: ESP-IDF, Arduino, ESPHome
5. Ordering & Compatibility
Sold by Espressif and distributors (DigiKey, Mouser, TME) as a bare module (also on dev boards like the ESP32-C3-DevKitM-1). Needs a carrier board + 3.3 V supply; add a momentary switch on a GPIO for a button build. Integrates via ESPHome/HA/MQTT/HTTP, or Matter-over-Wi-Fi.
6. Hackability & Known Issues
- Hackability: fully open (maximum). It is a blank programmable module — flash any firmware (ESPHome/Arduino/ESP-IDF), no vendor lock-in, fully local. This is the DIY end of the smart-button spectrum.
- Known issues: requires a carrier PCB + antenna clearance; single-core (vs S3); getting deep-sleep current low enough for coin-cell operation takes careful design; USB-serial/boot-strapping pins must be respected.
3 sources
- ESP32-C3 Wi-Fi & BLE 5 SoC — espressif.com
- ESP32-C3-MINI-1 & -1U Datasheet — espressif.com
- Espressif ESP32-C3-MINI-1 module — mouser.com
Openness & Hackability
Custom firmware: ESPHome, Tasmota, Arduino, MicroPython, ESP-IDF
Fully open platform. Runs any firmware. Hardware schematics open source. The reference for DIY smart buttons.
Specifications
|
Hackability
|
Fully open (max) — bare programmable module (ESPHome/Arduino/ESP-IDF), fully local
|
|
Smart Home Integrations
Compatible smart home platforms and voice assistants.
|
ESPHome, Home Assistant, MQTT, HTTP
|
|
Mcu
|
ESP32-C3 single-core RISC-V, up to 160MHz, 4MB flash
|
|
Max Operating Temp
Highest temperature the button is rated to operate in.
|
105°C
|
|
Min Operating Temp
Lowest temperature the button is rated to operate in.
|
-40°C
|
|
Protocol
The wireless communication standard. BLE = short range, phone direct. Zigbee = mesh network, needs hub. Z-Wave = mesh, needs hub. WiFi = direct, higher power.
|
WiFi 2.4GHz + BLE 5.0
|
|
Variants
|
-1 (PCB antenna) / -1U (external u.FL)
|
Installation Quick Reference
Setup: Pair with your hub or phone via WiFi 2.4GHz + BLE 5.0. Most smart buttons support single press, double press, and long press for three different actions.
Battery: Uses CR2032 battery. Expected life: 1-2 years. Low battery notification via the app.
Dimensions
Troubleshooting
Not responding to input
Check wiring continuity with a multimeter. Verify the contact block is properly seated. Inspect terminals for loose connections.
Where to Buy
Price range
$2.46 — $25.07
across 2 sellers in US dollars
Quick Specs
- Hackability
- Fully open (max) — bare programmable module (ESPHome/Arduino/ESP-IDF), fully local
- Smart Home Integrations
- ESPHome, Home Assistant, MQTT, HTTP
- Mcu
- ESP32-C3 single-core RISC-V, up to 160MHz, 4MB flash
- Max Operating Temp
- 105°C
- Min Operating Temp
- -40°C
What People Are Saying
“Not a button itself — the brain inside DIY smart buttons. Run ESPHome firmware and connect any physical button to create a custom WiFi or BLE smart button. Under $3 per module. Powers the maker/DIY sm”